Lightware UMX-HDMI-140 Series User Manual page 102


  
7. LW3 Programmers' Reference
Query the MAC Address
 GET·/MANAGEMENT/NETWORK.MacAddress
Apply Network Settings
 CALL·/MANAGEMENT/NETWORK:ApplySettings()
RS-232 Port Configuration
Protocol Setting
SET·/MEDIA/UART/P1.ControlProtocol=<protocol>

RS-232 Operation Mode
SET·/MEDIA/UART/P1.Rs232Mode=<mode>

BAUD Rate Setting
SET·/MEDIA/UART/P1.Baudrate=<baud_rate>

Databits Setting
SET·/MEDIA/UART/P1.DataBits=<databits>

Stopbits Setting
SET·/MEDIA/UART/P1.StopBits=<stopbits>

Parity Setting
SET·/MEDIA/UART/P1.Parity=<parity>

Command Injection Mode
SET·/MEDIA/UART/P1.CommandInjectionEnable=<logical_value>

RS-232 Recognizer
Enable the Recognizer
SET·/MEDIA/UART/P1.RecognizerEnable=<logical_value>

Set the Delimiter Hex
SET·/MEDIA/UART/RECOGNIZER.DelimiterHex=<delimiter>

Set the Timeout
SET·/MEDIA/UART/RECOGNIZER.TimeOut=<timeout>

Clear the Stored Last Recognized Serial Message
 CALL·/MEDIA/UART/RECOGNIZER:clear()
Query the Last Recognized Serial Message in String Format
 GET·/MEDIA/UART/RECOGNIZER.ActiveRx
Query the Last Recognized Serial Message in Hex Format
 GET·/MEDIA/UART/RECOGNIZER.ActiveRxHex
UMX-HDMI-140 series– User's Manual
Set the Active Timeout
Infrared Port Configuration
Enable Command Injection Mode
Change Command Injection Port Number
Enable/Disable Output Signal Modulation
Sending Message via the Communication Ports
Sending a TCP Message (ASCII-format) via TCP Port
Sending a TCP Text (ASCII-format) via TCP Port
Sending a TCP Binary Message (HEX-format) via TCP Port
Sending UDP Message (ASCII-format) via TCP Port
Sending a TCP Text (ASCII-format) via TCP Port
Sending a UDP Binary Message (HEX-format) via TCP Port
Sending a Message (ASCII-format) via Serial Port
Sending a Text (ASCII-format) via Serial Port
Sending a Binary Message (HEX-format) via Serial Port
Sending Pronto Hex Codes in Little-endian Format via IR Port
Sending Pronto Hex Codes in Big-endian Format via IR Port
Applied firmware package: v1.2.0 | LDC software: v2.4.1b7
SET·/MEDIA/UART/RECOGNIZER.ActivePropertyTimeout=<a_timeout>

SET·/MEDIA/IR/<ir_port>.CommandInjectionEnable=<ci_status>

SET·/MEDIA/IR/<in|out>.CommandInjectionPort=<port_no>

SET·/MEDIA/IR/D1.EnableModulation=<modulation>

 CALL·/MEDIA/ETHERNET:tcpMessage(<IP_address>:<port_no>=<message>)
 CALL·/MEDIA/ETHERNET:tcpText(<IP_address>:<port_no>=<text>)
 CALL·/MEDIA/ETHERNET:tcpBinary(<IP_address>:<port_no>=<HEX_message>)
 CALL·/MEDIA/ETHERNET:udpMessage(<IP_address>:<port_no>=<message>)
 CALL·/MEDIA/ETHERNET:udpText(<IP_address>:<port_no>=<text>)
 CALL·/MEDIA/ETHERNET:udpBinary(<IP_address>:<port_no>=<HEX_message>)
 CALL·/MEDIA/UART/<port>:sendMessage(<message>)
 CALL·/MEDIA/UART/<port>:sendText(<message>)
 CALL·/MEDIA/UART/<port>:sendBinaryMessage(<message>)
 CALL·/MEDIA/IR/<out>:sendProntoHex(<hex_code>)
 CALL·/MEDIA/IR/<out>:sendProntoHexBigEndian(<hex_code>)
102