Siemens SINUMERIK 840D Description Of Functions page 410

7 Configuring example
7.3 Safety Integrated with SPL
7.3.12 Appendix
Excerpt from symbol table:
Symbol
1 Hochlauf_ASUP_Start
2 Flanke_FB4_SPL_Start
3 Zyklus_FB4_SPL_Start
4 FB4_Start
5 FC9_SPL_Start
6 Teststop_aktiv
7 Teststop_1_starten
8 Teststop_1_ready
9 Teststop_2_starten
10 Teststop_2_ready
11 Teststop_2_error
12 Teststop_1_error
13 QUIT_NCK_error
14 Teststopphase_2_starten
15 Test_Stop_D_PLC
16 Test_Stop_C_PLC
17 Test_Stop_A_PLC
18 PLC_Stop_A_nicht_aktiv
19 Test_Stop_D_NCK
20 Test_Stop_C_NCK
21 Test_Stop_A_NCK
22 NCK_Stop_A_nicht_aktiv
23 Test_I/O_Peripherie_1
24 Test_I/O_Peripherie_2
25 Test_I/O_Peripherie_3
26 Test_I/O_Peripherie_4
27 Test_I/O_Peripherie_5
28 Fehler_Stop_D_PLC
29 Teststop_1_intern
30 Teststop_2_intern
31 QUIT_NCK_error_code
32 TIMER1
33 TIMER2
34 T_K_ABFALL
35 T_VERZUG_1
36 T_VERZUG_2
37 Teststop_Zeit_1
38 Teststop_Zeit_2
39 Teststop_Zeit_3
7-410
SINUMERIK 840D/SIMODRIVE 611 digital SINUMERIK Safety Integrated (FBSI) - Edition 11.03
Address Data type Comment
M 210.0 BOOL Run-up marker for SPL / ASUB start
M 210.1 BOOL Edge marker for SPL / FB4 start
M 210.2 BOOL Cycle marker for SPL / FB4 start
M 210.3 BOOL Interrupt number and polarity for SPL (FB4)
M 210.4 BOOL Start SPL
M 211.0 BOOL Activate test stop
M 211.1 BOOL Forced checking procedure of the shutdown paths (X, C)
M 211.2 BOOL Test stop1 performed without errors
M 211.3 BOOL Forced checking procedure of shutdown paths (Z)
M 211.4 BOOL Test stop 2 performed without errors
M 211.6 BOOL Error for test stop 2 (Z)
M 211.7 BOOL Error for test stop 1 (X, C)
M 214.4 BOOL Error for transfer using FC21
M 216.0 BOOL Start test of external stops
M 216.1 BOOL Trigger stop D in PLC / FC96
M 216.2 BOOL Trigger stop C in PLC / FC96
M 216.3 BOOL Trigger stop A in PLC / FC96
M 216.4 BOOL Stop A / PLC check not active
M 216.5 BOOL Trigger stop D via A 49.4 / PLC in NCK
M 216.6 BOOL Trigger stop C via A 49.3 / PLC in NCK
M 216.7 BOOL Trigger stop A via A 49.2 / PLC in NCK
M 217.0 BOOL Stop A / NCK check not active
M 217.1 BOOL Forced checking procedure of the I/O devices
M 218.0 BOOL Check Emergency Stop inputs
M 218.1 BOOL Start acknowledgement for Emergency Stop
M 218.2 BOOL Acknowledge Emergency Stop on the NCK side
M 218.3 BOOL Withdraw acknowledgment Emergency Stop on the
NCK side
M 218.7 BOOL Checkback input of contactors E 76.4 not OK.
MD 212 DWORD Run test stop 1 FC60 internally
MD 220 DWORD Run test stop 2 FC60 internally
MW 188 WORD Error code from FC21
T 20 TIMER STOP C -> STOP A (axes)
T 21 TIMER STOP C-> STOP A (spindle)
T 22 TIMER Drop-out time of contactors K1, K2
T 23 TIMER Delay time EMERGENCY STOP input
T 24 TIMER Delay time, acknowledgment
T 30 TIMER Monitoring duration 2h 40min
T 31 TIMER Monitoring duration 5h 20min
T 32 TIMER Monitoring duration 8h
© Siemens AG 2003 All Rights Reserved
11.03