TANDBERG Codec C Series Api Manual page 39

TANDBERG Codec C60 and Codec C40
Contents Contents Introduction Introduction
The Network settings,
continued...
xConfiguration Network [1..1] IEEE8021X Password
The 802.1X Password is the password needed for 802.1X authentication.
Value space: <S: 0, 32>
Format: String with a maximum of 32 characters.
Example: xConfiguration Network 1 IEEE8021X Password: "***"
xConfiguration Network [1..1] IEEE8021X AnonymousIdentity
The 802.1X Anonymous ID string is to be used as unencrypted identity with EAP (Extensible Authentication
Protocol) types that support different tunneled identity, like EAP-PEAP and EAP-TTLS. If set, the
anonymous ID will be used for the initial (unencrypted) EAP Identity Request.
Value space: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: xConfiguration Network 1 IEEE8021X AnonymousIdentity: ""
xConfiguration Network [1..1] IEEE8021X Eap Md5
Set the Md5 (Message-Digest Algorithm 5) mode. This is a Challenge Handshake Authentication Protocol
that relies on a shared secret. Md5 is a Weak security.
Value space: <On/Off>
On: The EAP-MD5 protocol is enabled (default).
Off: The EAP-MD5 protocol is disabled.
Example: xConfiguration Network 1 IEEE8021X Eap Md5: On
xConfiguration Network [1..1] IEEE8021X Eap Peap
Set the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients without the
need for client certificates. Developed by Microsoft, Cisco and RSA Security.
Value space: <On/Off>
On: The EAP-PEAP protocol is enabled (default).
Off: The EAP-PEAP protocol is disabled.
Example: xConfiguration Network 1 IEEE8021X Eap Peap: On
D14642.02—MAY 2010
xConfiguration
About the API About the API xConfiguration xConfiguration xCommand xCommand xStatus xStatus
The Network settings,
continued...
xConfiguration Network [1..1] IEEE8021X Eap TTLS
Set the TTLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients without the need
for client certificates. Developed by Funk Software and Certicom. Usually supported by Agere Systems,
Proxim and Avaya.
Value space: <On/Off>
On: The EAP-TTLS protocol is enabled (default).
Off: The EAP-TTLS protocol is disabled.
Example: xConfiguration Network 1 IEEE8021X Eap TTLS: On
xConfiguration Network [1..1] MTU
Set the Ethernet MTU (Maximum Transmission Unit).
Value space: <400..1500>
Range: Select a value from 400 to 1500bytes.
Example: xConfiguration Network 1 MTU: 1500
xConfiguration Network [1..1] Speed
Set the Ethernet link speed.
Value space: <Auto/10half/10full/100half/100full/1000full>
Auto: Autonegotiate link speed.
10half: Force link to 10Mbps half-duplex.
10full: Force link to 10Mbps full-duplex.
100half: Force link to 100Mbps half-duplex.
100full: Force link to 100Mbps full-duplex.
1000full: Force link to 1Gbps full-duplex.
Example: xConfiguration Network 1 Speed: Auto
xConfiguration Network [1..1] TrafficControl Mode
Set the network traffic control mode to decide how to control the the video packets transmission speed.
Value space: <On/Off>
On: Transmit video packets at maximum 20Mbps. Can be used to smooth out bursts in the outgoing
network traffic.
Off: Transmit video packets at link speed.
Example: xConfiguration Network 1 TrafficControl: On
39
API Guide
Appendices Appendices Contact us Contact us
www.tandberg.com