Technical Data - Auerswald COMmander Basic.2 Installation And Commissioning Instructions

Power Supply
Rated voltage 230 V
Rated current max. 0.8 A
Protection class I
Power max. 75 W
Module Power supply from the PBX
Environmental Requirements
Operation +0° ... +40° Celsius, avoid direct sunlight!
Operating the modules installed in the PBX casing
Storage and shipping -20° ... +70° Celsius
Humidity 10%- 90%, non-condensing
Connection Options on the Basic Unit
VoIP internal/external, 1 Ethernet port
PC and LAN
PC 1 USB port for a PC connection
Printer 1 serial port for a printer connection
Connection Options on the COMmander 8VoIP/16VoIP Module
VoIP internal/external, 2 Ethernet ports
PC and LAN as well as
a connection to the
basic unit
Connection Options on the COMmander VMF Module
PC and LAN as well as 2 Ethernet ports
a connection to the
basic unit
SD card 1 SD card slot
Connection Options on the COMmander S
ISDN external 1 external S
Measuring device 1 PMP port
Connection Options on the COMmander 4S
ISDN internal/external 4 S ports, optionally switchable as an
0
internal or external S
Connection Options on the COMmander 8S
ISDN internal/external 8 S ports, 4 of which are optionally
0
switchable as an internal or external S
(jumper); another 4 are permanently set as
internal S
Connection Options on the COMmander 8U
ISDN internal 8 U -ports
P0

Technical Data

10%, 50 Hz
Module
2M
port
2M
Module
0
port (jumper)
0
Module
0
port
0
ports
0
Module
P0
Important Information
Connection Options on the COMmander 8a/b Module
Analogue internal 8 internal analogue ports
Connection Options on the COMmander 2TSM Module
Door stations 1 power supply outlet
2 door terminal input/output jacks (1 per
door station)
4 relay outputs (2 for each door station)
4 ringer inputs; of which one is no longer
available for each alarm/announcement
contact connected
External devices to 6 relay outputs; of which two are no longer
switch available for each door station connected
Alarm/announcement 4 alarm inputs
contacts
Second ringer 1 second ringer output
Loud speaker/ 1 audio output
Playback device 1 music input
Internal Analogue Port
Connection unit Removable spring clamp connection
(2-core)
Type of dialling Pulse or tone dialling
Open-circuit voltage max. 40 VDC
Loop current approx. 23 mA
Range 2 x 50 , approx. 800 m at 0.6 mm
Ring tone approx. 45 V
Audible signals 425 Hz
Charge pulse configurable: 12/16 kHz
Impedances a/b symmetrical
Internal S Port
0
Connection unit Removable spring clamp connection
(4-core), on 2 ports per module, optional RJ-
45 socket
Connection type S basis access as Point-to-Multipoint
0
connection, EURO-ISDN (DSS1), short
passive bus
Supply voltage 40 V + 5% / – 15%
Feeder max. 4 W
End devices max. 2 end devices recommended (max. 8
ISDN end devices, of which max. 2 end
devices without separate power feed,
for example, different ISDN telephones)
Range max. 150 m with typical telephone or
network cable (twisted-pair) for bus setup;
European standards ENV 41001
[DINV 41001] and EN 28877 apply to IAE-
termination technology)
Terminators 100 , switchable; factory settings on
, configurable: 25/50 Hz
eff
5%, interval 10%
13