Lightware UMX-TPS-TX100 Series User Manual page 6


  
Table of Contents
7.7.4. Change the IP Address (Static) ..................................................... 87
7.7.5. Query the Subnet Mask .................................................................. 87
7.7.6. Change the Subnet Mask (Static) .................................................. 87
7.7.7. Query the Gateway Address .......................................................... 87
7.7.8. Change the Gateway Address (Static) .......................................... 88
7.8. RS-232 Port Configuration .......................................................88
7.8.1. Protocol Setting .............................................................................. 88
7.8.2. BAUD Rate Setting .......................................................................... 88
7.8.3. Databits Setting .............................................................................. 88
7.8.4. Stopbits Setting .............................................................................. 89
7.8.5. Parity Setting................................................................................... 89
7.8.6. RS-232 Operation Mode ................................................................. 89
7.8.7. Command Injection Enable ............................................................ 89
7.9. RS-232 Recognizer .....................................................................90
7.9.1. Enable the Recognizer .................................................................... 90
7.9.2. Set the Delimiter Hex ...................................................................... 90
7.9.3. Set the Timeout .............................................................................. 90
7.9.4. Query the Last Recognized Serial Message in String Format ..... 90
7.9.5. Query the Last Recognized Serial Message in Hex Format ......... 90
7.9.6. Query the Last Recognized Serial Message in Hash Format ...... 90
7.9.7. Clear the Stored Last Recognized Serial Message ...................... 91
7.9.8. Query the Last Recognized Serial Message in String Format ..... 91
7.9.9. Query the Last Recognized Serial Message in Hex Format ......... 91
7.9.10. Query the Last Recognized Serial Message in Hash Format .... 91
7.9.11. Set the Active Timeout ................................................................. 91
7.10. Infrared Port Configuration ..................................................91
7.10.1. Enable Command Injection Mode ............................................... 91
7.10.2. Enable/Disable Output Signal Modulation .................................. 91
7.11. Sending Message via the Communication Ports .....................92
7.11.1. Sending a TCP Message (ASCII-format) via TCP Port ............... 92
7.11.2. Sending a TCP Text (ASCII-format) via TCP Port ....................... 92
7.11.3. Sending a TCP Binary Message (HEX-format) via TCP Port ..... 92
7.11.4. Sending UDP Message (ASCII-format) via TCP Port ................. 92
7.11.5. Sending a TCP Text (ASCII-format) via TCP Port ....................... 93
7.11.6. Sending a UDP Binary Message (HEX-format) via TCP Port ..... 93
7.11.7. Sending a Message (ASCII-format) via Serial Port .................... 93
7.11.8. Sending a Text (ASCII-format) via Serial Port ............................. 93
7.11.9. Sending a Binary Message (HEX-format) via Serial Port ........... 93
7.11.10. Using Hexadecimal Codes......................................................... 93
7.11.11. Sending Pronto Hex Codes in Little-endian Format via IR Port . 94
7.11.12. Sending Pronto Hex Codes in Big-endian Format via IR Port .. 94
7.12. Sending CEC Commands ............................................................95
7.12.1. Sending an OSD String ................................................................. 95
UMX-TPS-TX100 series - User's Manual
7.12.2. Sending a CEC Command in Text Format................................... 95
7.12.3. Sending a CEC Command in Hexadecimal Format .................... 95
7.13. GPIO Port Configuration .........................................................96
7.13.1. Set the Direction of a GPIO Pin .................................................... 96
7.13.2. Set the Output Level of a GPIO Pin .............................................. 96
7.13.3. Toggle the Level of a GPIO Pin .................................................... 96
7.14. EDID Management .....................................................................96
7.14.1. Query the Emulated EDIDs ........................................................... 96
7.14.2. Query the Validity of a Dynamic EDID ......................................... 97
7.14.3. Query the Preferred Resolution of an User EDID ........................ 97
7.14.4. Emulating an EDID to an Input Port ............................................. 97
7.14.5. Emulating an EDID to All Input Ports ........................................... 97
7.14.6. Copy an EDID to User Memory .................................................... 97
7.14.7. Deleting an EDID from User Memory .......................................... 97
7.14.8. Resetting the Emulated EDIDs ..................................................... 97
7.15. LW3 Commands - Quick Summary .............................................98
8. FIRMWARE UPGRADE ....................................................................102
8.1. About the Firmware Package (LFP2 File) .................................102
8.2. Short Instructions ..................................................................102
8.3. Installation of LDU2 ...............................................................102
8.4. Detailed Instructions ..............................................................102
8.4.1. Establish Connection ................................................................... 102
8.4.2. Start the LDU2 Application and Follow the Steps ...................... 102
8.5. Keeping the Configuration Settings .......................................105
8.6. Remote Firmware Upgrade of Connected Lightware Devices .106
9. TROUBLESHOOTING ......................................................................107
9.1. Use Cases ..................................................................................107
9.2. How to Speed Up the Troubleshooting Process .....................109
10. TECHNOLOGIES ............................................................................ 110
10.1. EDID Management ...................................................................110
10.1.1. Understanding the EDID ............................................................. 110
10.1.2. Advanced EDID Management .................................................... 110
10.2. HDCP Management .................................................................111
10.2.1. Protected and Unprotected Content ......................................... 111
10.2.2. Disable Unnecessary Encryption ............................................... 111
10.3. Pixel Accurate Reclocking ...................................................112
11. APPENDIX ...................................................................................... 113
11.1. Specification ..........................................................................113
11.2. Factory Default Settings ......................................................115
11.3. Content of Backup File ..........................................................115
11.4. Cable Wiring Guide .................................................................116
11.4.1. Cable Wiring Guide for Serial Data Transmission .................... 116
11.4.2. Audio Cable Wiring Guide .......................................................... 116
11.5. Mechanical Drawings ............................................................117
11.5.1. UMX-TPS-TX100 series .............................................................. 117
11.5.2. WP-UMX-TPS-TX100 series ....................................................... 118
11.5.3. FP-UMX-TPS-TX100 series ........................................................ 118
11.6. Port Numbering ......................................................................119
11.6.1. WP-UMX-TPS-TX120-US ............................................................ 119
11.6.2. WP-UMX-TPS-TX130-US / WP-UMX-TPS-TX130-US-Plus........ 119
11.6.3. UMX-TPS-TX120 ......................................................................... 119
11.6.4. UMX-TPS-TX130 ......................................................................... 119
11.6.5. UMX-TPS-TX140 / UMX-TPS-TX140-Plus ................................. 120
11.6.6. FP-UMX-TPS-TX120 ................................................................... 120
11.6.7. FP-UMX-TPS-TX130 ................................................................... 120
11.7. Maximum Extension Distances ...............................................120
11.8. Factory EDID List ...................................................................121
11.9. Release Notes of the Firmware Packages .............................122
11.10. Further Information ............................................................124
6