Analog Stereo Audio (Jack); Analog Stereo Audio (Phoenix); Ethernet Connector (Tps And Lan Ports); Connector - Lightware UMX-TPS-TX100 Series User Manual


  
3. Product Overview
3.7.7. Analog Stereo Audio (Jack)
The connector is used for receiving unbalanced analog audio
signal. It is also known as (3.5 mm or approx. 1/8") audio jack,
phone jack, phone plug and mini-jack plug.
Pin nr. Signal
1 2 3
1
2 Right
3 Ground
Jack audio plug pin assignments
You can find more information about audio functions in the
Interface section.
3.7.8. Analog Stereo Audio (Phoenix)
5-pole Phoenix connector is used for balanced
analog audio input in the UMX-TPS-TX140 and
UMX-TPS-TX140-Plus transmitters. Unbalanced audio signals can
be connected as well. See more details about the balanced and
unbalanced input port wiring in the Audio Cable Wiring Guide
Pin nr.
1
2
1 2 3 4 5
3
4
5
Analog audio connector and plug pin assignments
Compatible Plug Type
Phoenix Combicon series (3.5mm pitch, 5-pole), type: MC 1.5/5-ST-3.5.
®
You can find more information about analog audio function in the
Audio Interface section.
3.7.9. Ethernet Connector (TPS and LAN Ports)
The extender provides standard RJ45 connectors for TPS IN and
LAN ports. Always use high quality Ethernet cable for connecting
transmitters and receivers. Maximum CATx cable distances can be
found in the
Left
Audio
LAN connector
Wiring of TPS and LAN Cables
Lightware recommends the termination of LAN cables on the basis of
TIA/EIA T 568 A or TIA/EIA T 568 B standards.
section.
Signal
Left+
Left-
Pin
Ground
1
Right-
2
Right+
3
4
5
6
7
8
You can find more information about TPS interface in the
section.
UMX-TPS-TX100 series – User's Manual
Maximum Extension Distances section.
8 1 1 8 8
TPS connector of TPS connector of FP/
UMX-TPS-TX100 WP-UMX-TPS-TX100
series transmitters series transmitters
8 1
1 8
Top Bottom
TIA/EIA T568 A Color and name TIA/EIA T568 B Color and name
white/green stripe white/orange stripe
green solid orange solid
white/orange stripe white/green stripe
blue solid blue solid
white/blue stripe white/blue stripe
orange solid green solid
white/brown stripe white/brown stripe
brown solid brown solid
Pin assignments of RJ45 connector types
3.7.10. RS-232 Connector
The extender contains a 3-pole Phoenix connector which is
used for RS-232 serial connection.
1 2 3
1
RS-232 connector pin assignments
Compatible Plug Type
Phoenix Combicon series (3.5mm pitch, 3-pole), type: MC 1.5/3-ST-3.5.
®
You can find more information about RS-232 interface in the
Serial Interface section.
3.7.11. IR Connector
IR detector and IR emitter can be connected to the
UMX-TPS-TX100 series extenders with TRS (Tip, Ring, and
Sleeve) connectors. They are also known as (3,5 mm or approx.
1/8") audio jack, phone jack, phone plug, and mini-jack plug. The pin
assignments are the following for the detector and the emitter:
Side
1 2 3
Detector – 3-pole-TRS
1 Tip Signal (active low)
2 Ring GND
3 Sleeve +5V
INFO: Ring pole of the emitter is optional. If your IR emitter has
three-pole TRS plug, then the Ring and the Sleeve are the same
signal (Output - ).
You can find more information about Infrared interface in the
IR Interface section.
3.7.12. IR Detector
TPS Interface
FP/WP-UMX-TPS-TX100 series transmitters are built with an IR
detector on front panel of the wall plate. The sensor is used for
receiving IR signals from remote control or other IR emitter devices.
You can find more information about Infrared interface in the
IR Interface section.
27
Pin nr. Signal
1 Ground
2 TX data
3 RX data
1 2-3
Emitter – 2-pole-TS
1 Tip +5V
2 Ring
Signal (active low)
3 Sleeve