Reset To Factory Default Settings; Reseting The Device; Control Lock; Entering Firmware Upgrade Mode - Lightware UMX-TPS-TX100 Series User Manual


  
4. Operation
4.4.2. Reset to Factory Default Settings
VGA IN AUDIO1 IN HDMI IN DP IN
To restore factory default
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
values, do the following steps:
VIDEO AUDIO SHOW
SELECT SELECT ME
Ethernet
INPUT STATUS
VGA AUDIO
DP DP
HDMI HDMI
IR
Autoselect TPS LINK
VIDEO AUDIO RESET
VGA IN AUDIO IN DP IN HDMI IN
Step 1. Make sure the device is powered on and operational.
Step 2. Press and keep pressed the Show Me button for 10 seconds.
After 5 seconds front panel LEDs start blinking but keep on
pressing the button.
Step 3. After 10 seconds the LEDs start blinking faster; release the
button and press it 3 times again quickly (within 3 seconds).
Step 4. The LEDs get dark, the device restores the factory default
settings and reboots.
Factory default settings are listed in the
section.
4.4.3. Reseting the Device
VGA Audio1 HDCP RESET
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO AUDIO SHOW
INPUT STATUS SELECT SELECT ME
Step 1. Push the button with a thin object for a second.
Step 2. Wait until the device reboots. You can use the transmitter when
ATTENTION! Reseting the device does not reset the settings to
factory defaults. To reset factory default settings see the previous
section.
4.4.4. Control Lock
Factory Default Settings
UMX-TPS-TX100 series – User's Manual
VGA Audio1 HDCP
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO
VGA IN AUDIO1 IN HDMI IN DP IN INPUT STATUS SELECT
In few cases (after firmware
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
upgrade, etc) you may need
to reset the device. Pushing
the reset button results the
VIDEO AUDIO SHOW
SELECT SELECT ME
same as you disconnect and
Ethernet
INPUT STATUS reconnect the power adaptor
VGA AUDIO
DP DP
to the transmitter. To reseting
HDMI HDMI
Autoselect TPS LINK IR
VIDEO AUDIO RESET
the device follow the steps:
VGA IN AUDIO IN DP IN HDMI IN
the LIVE LED is blinking slowly again.
VGA Audio1 HDCP
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO
VGA IN AUDIO1 IN HDMI IN DP IN INPUT STATUS SELECT
Press the Audio Select and
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
buttons
Show Me
(within 100 ms) to disable/
enable front panel buttons;
VIDEO AUDIO SHOW
SELECT SELECT ME
front panel LEDs blink 4 times
Ethernet
INPUT STATUS when locking/unlocking. If
VGA AUDIO
DP DP
HDMI HDMI the control lock is enabled
IR
Autoselect TPS LINK
VIDEO AUDIO RESET
and a button is pressed, front
panel LEDs blink 3 times.
VGA IN AUDIO IN DP IN HDMI IN
4.4.5. Entering Firmware Upgrade Mode
RESET
AUDIO SHOW
SELECT ME VGA IN AUDIO1 IN HDMI IN
VIDEO AUDIO
SELECT SELECT
Ethernet
INPUT STATUS
VGA AUDIO
DP DP
HDMI HDMI
Autoselect TPS LINK
VIDEO AUDIO
VGA IN AUDIO IN DP IN
Step 1. Make sure the transmitter is powered off.
Step 2. Press and keep pressed the Show Me button.
Step 3. Power on the transmitter while the Show Me button is being
pressed. If the device is switched to firmware upgrade mode
the LIVE LED is blinking quickly (less than 500 ms duty cycle).
The other LEDs are off.
The procedure of firmware upgrade can be found in the
Upgrade chapter.
4.5. Software Control Modes
RESET
AUDIO SHOW
User has more possibilities to control the device besides the front
SELECT ME
panel buttons. The following list contains the software control modes:
together
▪ Lightware Device Controller (LDC) - you can connect to the device
via our control software using Ethernet or RS-232 interface and
control or configure the device as you wish. For the details see
the Software Control - Lightware Device Controller
▪ LW2 protocol commands: you can configure the device by using
the reduced command set of LW2 protocol. For more details
see the LW2 Programmer's Reference
▪ LW3 protocol commands: you can configure the device by using
the full-range command set of LW3 protocol. For more details
see the LW3 Programmers' Reference
40
VGA Audio1 HDCP RESET
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO AUDIO SHOW
DP IN INPUT STATUS SELECT SELECT ME
It may happen that the
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
firmware upgrade process
is not successful and the
device cannot be switched to
SHOW
ME
bootload mode automatically.
In this case, the device can be
forced into firmware upgrade
IR
RESET
mode as follows:
HDMI IN
Firmware
chapter.
chapter.
chapter.