Rear View - Fp-Umx-Tps-Tx100 Series; Electrical Connections; Locking 12V Dc Connection; Dc Connection - Lightware UMX-TPS-TX100 Series User Manual


  
3. Product Overview
3.6. Rear View - FP-UMX-TPS-TX100 series
3
1 2
TPS output Locking RJ45 connector for HDBaseT
1
(PoE) transmission. Maximum CATx cable distances
can be found in the
Distances section.
RS-232 3-pole Phoenix connector for controlling the
2
connector device with LDC or third-party control systems,
or third-party device control. Pin assignment
can be found in the
3 48V DC Power the device remotely by a PoE-compatible
input power injector (TPS-PI-1P1). If the device has
to be powered by a local adaptor (PSU-48VP1),
connect the output to the 2-pole Phoenix
connector on the rear of the floor plate. See
more details about powering options in the
48V DC Connection
available Powering
3.7. Electrical Connections
3.7.1. Locking 12V DC Connection
UMX-TPS-TX100 series transmitters are built with locking 12V DC
connector. Do not forget to turn the plug clockwise direction before
disconnecting the power adaptor.
WARNING! Always use the supplied 12V power adaptor. Warranty
void if damage occurs due to use of a different power source.
signal
TM
3.7.2. 48V DC Connection
Maximum Extension
FP/WP-UMX-TPS-TX100 series transmitters are built with
2-pole Phoenix connector for 48V DC 1A power connection.
1
RS-232 Connector section.
3.7.3. VGA Connector
The transmitter provides a standard 15-pole
D-SUB female connector for connecting VGA
devices. Always use high-quality VGA cable for
section or see all the connecting sources and displays; using a VGA cable where all the pins
Options. are wired (including the DDC channel's wires) is highly recommended.
3.7.4. HDMI Connector
The extender provides standard 19 pole HDMI connector
for input. Always use high quality HDMI cable for
connecting sources and displays.
UMX-TPS-TX100 series – User's Manual
P I P I
N : N :
2 . 1 2 . 1
m
m
1 2 1 2
V V
1 A D 1 A D C
C
Locking DC connector
Pin nr. Signal
2
1 +
2 -
2-pole Phoenix connector and plug pin assignments
3.7.5. DisplayPort Connector
UMX-TPS-TX140, UMX-TPS-TX140-Plus, WP-UMX-TPS-
TX130-US, and WP-UMX-TPS-TX130-US-Plus models
provide standard 20-pole DisplayPort connector for input. Always use
high quality DP cable for connecting DisplayPort devices.
3.7.6. DVI-I Connector
m
m
UMX-TPS-TX130, UMX-TPS-TX140,
transmitters provide a standard 29-pole DVI-I connector for input
where digital and analog pins are connected internally. Hence users
can use the connector receiving DVI-A (analog video) and DVI-D
signals (digital video and digital audio) as well.
ATTENTION! Only one (DVI-A or DVI-D) mode is available at a time.
You can use the Video Select button to choose the input source.
Always use high quality DVI cable for connecting DVI devices.
The following drawing and table show the pinout of DVI-I connector
and the position of analog and digital signal pins.
1
9 10 11
17 18 19
Pin Signal
1 TMDS Data2-
2 TMDS Data2+
3 TMDS Data2 Shield
4 not connected
5 not connected
6 DDC Clock
7 DDC Data
8 Analog Vertical Sync
9 TMDS Data1-
10 TMDS Data1+
11 TMDS Data1 Shield
12 not connected
13 not connected
14 +5V Power
15 GND (for +5V)
26
and UMX-TPS-TX140-Plus
2 3 4 5 6 7 8
C1 C2
12 13 14 15 16
C3 C4
20 21 22 23 24
C5
Pin Signal
16 Hot Plug Detect
17 TMDS Data0-
18 TMDS Data0+
19 TMDS Data0 Shield
20 not connected
21 not connected
22 TMDS Clock Shield
23 TMDS Clock+
24 TMDS Clock-
C1 Analog Red
C2 Analog Green
C3 Analog Blue
C4 Analog Horizontal Sync
C5 GND