Front Panel Buttons; Video Select Button; Audio Select Button; Port Legend - Lightware UMX-TPS-TX100 Series User Manual


  
4. Operation
4.3. Front Panel Buttons
INFO: WP-UMX-TPS-TX130-US and FP-UMX-TPS-TX130-MKM
models have the same functionality. The operation of the front
panel buttons is also similar.
4.3.1. Video Select Button
VGA IN AUDIO1 IN HDMI IN DP IN
Desired video input can be
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
selected by the Video Select
button from the front panel.
The selection order of the
VIDEO AUDIO SHOW
SELECT SELECT ME
inputs depends on the model
Ethernet
as follows:
INPUT STATUS
VGA AUDIO
DP DP
HDMI HDMI
IR
Autoselect TPS LINK
VIDEO AUDIO RESET
VGA IN AUDIO IN DP IN HDMI IN
VGA
UMX-TPS-TX120:
VGA
UMX-TPS-TX130:
VGA HDMI
UMX-TPS-TX140:
VGA
WP-UMX-TPS-TX120-US:
VGA
WP-UMX-TPS-TX130-US:
VGA
FP-UMX-TPS-TX130-MKM:
4.3.2. Audio Select Button
VGA Audio1 HDCP RESET
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO AUDIO SHOW
INPUT STATUS SELECT SELECT ME
UMX-TPS-TX120:
UMX-TPS-TX130:
Autoselect
HDMI
UMX-TPS-TX140:
HDMI DVI-D DVI-A
Autoselect
WP-UMX-TPS-TX120-US:
DP DVI-D DVI-A
Autoselect
WP-UMX-TPS-TX130-US:
HDMI Autoselect
FP-UMX-TPS-TX130-MKM:
HDMI Autoselect
DP
INFO: Embedded digital audio is received on the digital video input
port (HDMI / DP / DVI-D) which is currently selected. If analog
HDMI DP Autoselect
video input signal (VGA / DVI-A) is selected which cannot contain
embedded audio, this source is skipped.
4.3.3. Port Legend
Video only
1
UMX-TPS-TX100 series – User's Manual
VGA Audio1 HDCP
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO
VGA IN AUDIO1 IN HDMI IN DP IN INPUT STATUS SELECT
Desired audio input can be
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
selected by the Audio Select
button from the front panel.
The selection order of the
VIDEO AUDIO SHOW
SELECT SELECT ME
inputs depends on the model
Ethernet
as follows:
INPUT STATUS
VGA AUDIO
DP DP
HDMI HDMI
IR
Autoselect TPS LINK
VIDEO AUDIO RESET
VGA IN AUDIO IN DP IN HDMI IN
Analog audio Embedded digital audio
Analog audio Embedded digital audio
Audio1 Audio2 Embedded audio
Analog audio Embedded digital audio
Analog audio Embedded digital audio
Analog audio Embedded digital audio
Audio only 2 Video with embedded
1
audio
4.3.4. Programmable Show Me Button
RESET
AUDIO SHOW
SELECT ME
VGA IN AUDIO1 IN HDMI IN
VIDEO AUDIO
SELECT SELECT
Ethernet
INPUT STATUS
VGA AUDIO
DP DP
HDMI HDMI
Autoselect TPS LINK
VIDEO AUDIO
VGA IN AUDIO IN DP IN
4.4. Special Functions
4.4.1. Enable DHCP (Dynamic) IP Address
VGA IN AUDIO1 IN HDMI IN
VIDEO AUDIO
SELECT SELECT
Ethernet
INPUT STATUS
VGA AUDIO
DP DP
HDMI HDMI
Autoselect TPS LINK
VIDEO AUDIO
VGA IN AUDIO IN DP IN
Step 1. Make sure the device is powered on and operational.
Step 2. Press and keep pressed the Show Me button for 5 seconds.
Step 3. After 5 seconds front panel LEDs start blinking; release the
button and press it 3 times again quickly (within 3 seconds).
Step 4. The LEDs get dark, DHCP gets enabled.
39
VGA Audio1 HDCP RESET
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO AUDIO SHOW
DP IN INPUT STATUS SELECT SELECT ME
Action or an operation can
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
be assigned to the Show
Me button. "Show Me button
pressed" is a condition that
SHOW
ME
can be selected in the Event
Manager. See more details in
the Event Manager section.
IR
RESET
HDMI IN
VGA Audio1 HDCP RESET
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO AUDIO SHOW
DP IN INPUT STATUS SELECT SELECT ME
The device has a static IP
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
address as a factory default
setting. If this setting does
not fit to the circumstances
SHOW
ME
during install or usage, DHCP
can be enabled from the front
panel:
IR
RESET
HDMI IN