Rear View - Umx-Tps-Tx100 Series; Front View - Wp-Umx-Tps-Tx100 Series - Lightware UMX-TPS-TX100 Series User Manual


  
3. Product Overview
3.2. Rear View - UMX-TPS-TX100 series
UMX-TPS-TX120
1 2
UMX-TPS-TX130
1 2
UMX-TPS-TX140 /
1 2
UMX-TPS-TX140-Plus
1 12V DC input 12V DC input for local powering. For more details see the
Connection section or see all the available
2 RS-232 3-pole Phoenix connector for controlling the device with LDC or third-party control
connector systems, or third-party device control. Pin assignment can be found in the
Connector section.
3 GPIO 8-pole Phoenix connector for configurable general purpose input/output ports. Pin
assignment can be found in the
Ethernet Locking RJ-45 connector for configuring the device using Lightware Device
4
Controller (LDC), or upgrading it using Lightware Device Updater (LDU). Any third-
party control system can use this port to control the device.
TPS OUT Locking RJ45 connector for HDBaseT
5
(PoE) cable distances can be found in the
6 Status LEDs The LEDs give feedback about the actual state of the device. See the details in the
Rear Panel LEDs
7 IR IN and 3-pole TRS connector, also known as 3.5 mm (1/8") jack plug for optional IR
OUT receiver (IR IN) and transmitter (IR OUT) connection. Pin assignments can be
found in the IR Connector
Audio2 input 5-pole Phoenix connector for balanced analog audio input. Pin assignment can
8
be found in the
DVI-I input DVI-I connector for analog / DVI / HDMI signals. Pin assignment can be found in
9
the DVI-I Connector
4 5 6 7
3 4 5 6 7 9
3 4 5 6 7 8 9
Powering Options.
GPIO - General Purpose Input/Output Ports
signal transmission. Maximum CATx
TM
Maximum Extension Distances
section.
section.
Analog Stereo Audio (Phoenix) section.
section.
UMX-TPS-TX100 series – User's Manual
3.3. Front View - WP-UMX-TPS-TX100 series
WP-UMX-TPS-TX120-US
2
3
4
5
6
1 Input Status LEDs
Locking 12V DC
Audio Select button
2
Video Select button
3
RS-232
Ethernet
4
section.
VGA input
5
6 Audio input
section.
Show Me button
7
Reset button
8
9 IR detector
q HDMI input
w DisplayPort input
WP-UMX-TPS-TX130-US / WP-UMX-TPS-TX130-US-Plus
1
7 2
3
8
4
9
5
q
6
LEDs give feedback about the current status of the unit and input signals.
See the details in the Front Panel LEDs
Button for switching between audio sources. See the details in the
Select Button section.
Button for switching between video sources. See the details in the
Select Button section.
Locking RJ-45 connector for configuring the device using Lightware
Device Controller (LDC), or upgrading it using Lightware Device Updater
(LDU). Any third-party control system can use this port to control the
device.
D-SUB connector for analog video signal.
3.5 mm Jack connector for asymmetric analog audio input signal.
Special functions can be reached using this button (firmware upgrade
(bootload) mode, DHCP settings, restore factory default settings,
condition launching in Event Manager).
Pushing the button reboots the unit.
IR Detector can sense IR light which can be forwarded to the receiver
side or use for controlling functions.
HDMI connector for DVI video or HDMI video and audio.
DisplayPort connector for DisplayPort audio/video signal.
24
1
7
8
9
q
w
section.
Audio
Video