Tps Link Led; Firmware Version Indication; Rear Panel Leds; Live Led - Lightware UMX-TPS-TX100 Series User Manual


  
4. Operation
4.1.5. TPS LINK LED
OFF:
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
No TPS link between
transmitter and the receiver.
VIDEO AUDIO SHOW
SELECT SELECT ME
BLINKING (slow):
Ethernet
INPUT STATUS
Low power mode is active.
VGA AUDIO
DP DP
HDMI HDMI
IR
Autoselect TPS LINK
VIDEO AUDIO RESET
BLINKING (fast):
Ethernet fallback mode is
VGA IN AUDIO IN DP IN HDMI IN
active.
ON:
TPS
HDBaseT or Long Reach
mode is active.
You can find more details about TPS operation modes in the
TPS Interface section.
4.1.6. Firmware Version Indication
After being powered on, the transmitter lights up all LEDs, then displays
its firmware version using three LEDs on the front panel: the upper
three in the left column. The top LED means the first number of the
firmware version – actually this is the main version. The second and
the third LEDs from the top indicate the second and the third numbers
of the firmware version which mean the subversions.
VGA Audio1 HDCP
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
1.3.2
INPUT STATUS
UMX-TPS-TX140
Example - WP-UMX-TPS-TX130-US
The process after the device is switched on or rebooted is the
following:
Step 6. VGA LED blinks once the first number (1).
Step 7. DP LED blinks twice the second number (2).
Step 8. HDMI LED stays dark showing the third number (0).
4.2. Rear Panel LEDs
4.2.1. LIVE LED
the
PIN: 2.1mm
RS-232
12V 1A DC
OFF:
BLINKING (slow):
BLINKING (fast):
ON:
link is established,
4.2.2. RS-232 LED
PIN: 2.1mm
RS-232
12V 1A DC
OFF:
BLINKING:
ON:
See more details about RS-232 modes in the
INPUT STATUS section.
VGA AUDIO
DP DP
4.2.3. SRVC LED
HDMI HDMI
Autoselect TPS LINK
VIDEO AUDIO
1.4.0
PIN: 2.1mm
RS-232
WP-UMX-TPS-TX130-US
12V 1A DC
ON:
See more details about Test pattern input mode in the
section.
UMX-TPS-TX100 series – User's Manual
GPIO LIVE 5 AUDIO2 IN
RS-232
SRVC
LINK
2 3 4 5 6 7 Ethernet IR IN IR OUT
TX RX 1 L R
The device is not powered.
The device is powered and operational.
The device is in firmware upgrade (bootload)
mode.
The device is powered but not operational.
LIVE
GPIO 5 AUDIO2 IN
RS-232
SRVC
LINK
TX RX 1 2 3 4 5 6 7 Ethernet IR IN IR OUT L R
RS-232 ports (Local and Link) are in Pass-
through mode.
Command injection mode is active.
RS-232 ports (Local and Link) are in Control
mode.
Technical Background
LIVE
GPIO 5 AUDIO2 IN
RS-232
SRVC
LINK
TX RX 1 2 3 4 5 6 7 Ethernet IR IN IR OUT L R
Test pattern is the selected and active input
source.
4.2.4. LINK LED
PIN: 2.1mm
RS-232 GPIO
12V 1A DC TX RX 1 2 3 4 5 6 7
OFF: No TPS link between the transmitter and the
5 DVI-I IN
receiver.
BLINKING (slow): Low power mode is active.
BLINKING (fast): Ethernet fallback mode is active.
ON: TPS link is established, HDBaseT or Long Reach
mode is active.
See more details about TPS modes in the
5 DVI-I IN
5 DVI-I IN
Test Pattern
38
LIVE 5 AUDIO2 IN
RS-232
SRVC
LINK
Ethernet IR IN IR OUT L R 5 DVI-I IN
TPS Interface section.