Operation; Front Panel Leds; Video Input Leds; Audio Input Leds - Lightware UMX-TPS-TX100 Series User Manual


  

4. Operation

4
O peration
This chapter is about the powering and operating of the device describing the
functions which are available by the front/rear controls:
Further Built-in Features
Î

Front Panel LEDs

Î
Rear Panel LEDs
Î
Front Panel Buttons
Î
Special Functions
Î
UMX-TPS-TX100 series – User's Manual
4.1. Front Panel LEDs
INFO: The operation of the status LEDs of WP-UMX-TPS-TX100
series and FP-UMX-TPS-TX100 series models are the same.
ATTENTION! When Dark mode is enabled, no LEDs are on, even
though the device is fully functional.
4.1.1. Video Input LEDs
VGA
HDMI
DP
DVI-D
VIDEO
VGA IN AUDIO1 IN HDMI IN DP IN INPUT STATUS
OFF: Video source is not
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
selected.
BLINKING: Video source is
VIDEO AUDIO SHOW
SELECT SELECT ME
selected, and signal is not
Ethernet
detected.
INPUT STATUS
VGA AUDIO
DP DP
HDMI HDMI
Autoselect TPS LINK IR ON: Video source is selected
VIDEO AUDIO RESET
and signal is present.
VGA IN AUDIO IN DP IN HDMI IN
4.1.2. Audio Input LEDs
VIDEO
VGA IN AUDIO1 IN HDMI IN DP IN
OFF: Audio source is not
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
selected.
BLINKING: Audio source is
VIDEO AUDIO SHOW selected, and signal is not
SELECT SELECT ME
detected.
Ethernet
INPUT STATUS
ON
VGA AUDIO
DP DP
HDMI HDMI
IR
Autoselect TPS LINK Audio source is selected
VIDEO AUDIO RESET
and the port is active but not
embedded to the output video
DP IN HDMI IN
VGA IN AUDIO IN
stream (DVI output mode).
ON
source is selected, the port
is active and the audio is
embedded to the output video
stream (HDMI output mode).
4.1.3. Autoselect LED
VGA IN
RESET
Audio1 HDCP
HDMI Autoselect
DP DVI-A Video
DVI-D Audio2
AUDIO
VIDEO AUDIO SHOW
SELECT SELECT ME
You can find more details in the
4.1.4. HDCP LED
VGA IN
VGA Audio1 HDCP RESET
HDMI HDMI Autoselect
DVI-A Video OFF:
DP DP
DVI-D DVI-D Audio2
AUDIO
VIDEO AUDIO SHOW
Video output signal is not encrypted with HDCP.
INPUT STATUS SELECT SELECT ME
ON:
Video output signal is HDCP-encrypted.
You can find more details in the
(with short pause):
(continuously): Audio
VGA Audio1 HDCP
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO
AUDIO1 IN HDMI IN DP IN INPUT STATUS SELECT
OFF:
W W P P - - U U M M X X - - T T P P S S - - T T X X 1 1 3 3 0 0 - - U U S S
Autoselect function
disabled.
VIDEO AUDIO SHOW
SELECT SELECT ME BLINKING:
Autoselect function
Ethernet
INPUT STATUS
VGA AUDIO
enabled, searching for signal
DP DP
HDMI HDMI
IR
Autoselect TPS LINK
(the video input LEDs are also
VIDEO AUDIO RESET
blinking).
VGA IN AUDIO IN DP IN HDMI IN ON:
Autoselect function
enabled, the active video
signal is found (the selected
video input's LED is also ON).
The Autoselect Feature section.
VGA Audio1 HDCP
HDMI HDMI Autoselect
DP DP DVI-A Video
DVI-D DVI-D Audio2
VIDEO AUDIO
VIDEO
AUDIO1 IN HDMI IN DP IN INPUT STATUS SELECT
HDCP Management section.
37
RESET
AUDIO SHOW
SELECT ME
is
is
is
RESET
AUDIO SHOW
SELECT ME