Advertisement
Parameter Name
Parameter
Modbus
Digital Operator
No.
Address
Display
Pre-Charge Level
P4-01
0115H
Pre-Charge Level
P4-02
Pre-Charge Frequency
0116H
Pre-Charge Freq.
P4-03
Pre-Charge Time
0117H
Pre-Charge Time
Thrust Bearing
P4-04
0118H
Acceleration Time
Thrust Acc. Time
Thrust Bearing
P4-05
0119H
Frequency
Thrust Freq.
P4-06
Thrust Bearing
011AH
Deceleration Time
Thrust Dec Time.
<0032>
Feedback Fault Auto
P4-07
011BH
Restart Enable
<0032>
Fdback Flt Rstrt
Denotes that parameter can be changed when the Drive is running.
196
Description
Pump Advanced
Sets the level when the drive will run at the pre-charge frequency (P4-
02). The Drive will stop when one of the following conditions occurs:
Feedback signal rises above P4-01 level, pre-charge timer P4-03
expires, or low water digital input is deactivated (H1-XX = 85).
The pre-charge function can only be activated while in a stop
condition. The function is enabled by setting P4-03 to a value greater
than 0. When the function is activated, the drive's operator display
indicates a "Pre-charge" alarm.
Note: This function is only active in the stopped mode.
Thrust Mode: The pre-charge level is used when the thrust mode is
active for the feedback check. The thrust mode is deactivated when the
feedback exceeds the programmed level in P4-01. A value of 0 disables
the thrust mode feedback check function.
Sets the frequency reference used when the pre-charge function is
active.
Sets the maximum allowed pre-charge time. A value of 0 disables this
function.
Sets the thrust bearing acceleration time. When enabled (P4-05>0), the
Drive output frequency will ramp up to the specified thrust bearing
frequency reference in P4-05 using an acceleration time as specified in
P4-04. The PI mode is automatically disabled.
Once the output frequency reaches the programmed thrust bearing
frequency, the Drive automatically switches to PI control and the
original acceleration time (C1-01), and will continue in the normal
operation (auto) mode, unless Pre-Charge is enabled, in which case
Pre-Charge mode occurs.
This function active in the Hand Mode and Auto Mode.
. Note: In Auto Mode , the Minimum Pump Frequency will become the
thrust bearing frequency if smaller than the thrust bearing frequency in
P4-05.
In Hand Mode , the minimum frequency is P4-05 when the thrust
mode is enabled. The Pre-Charge level is not active in the hand mode.
Sets the frequency reference used when the thrust bearing function is
active.
A value of 0 disables this function.
This deceleration time will be used to bring the Drive from Thrust
Frequency (P4-05) to stop when Thrust Mode is active. Any time the
Run Command is removed while the drive is operating in the Thrust
Mode above the Thrust Frequency, this deceleration time will be used
once the frequency reference is at or below the Thrust Frequency.
Note: In Auto Mode , the Minimum Pump Frequency (P1-06) will
become the thrust bearing frequency if smaller than the thrust bearing
frequency in P4-05.
In Hand Mode , the minimum frequency is P4-05 when the thrust
mode is enabled. The Pre-Charge level is not active in the hand mode.
Setting to enable / disable Auto Restart for the following iQpump
transducer / feedback faults (N = disable / Y = enable):
LL: Low Level Feedback (P1-07)
HL: High Level Feedback (P1-09)
TL: Transducer Loss (b5-12)
0: TL = N HL = N LL = N
1: TL = N HL = N LL = Y
2: TL = N HL = Y LL = N
3: TL = N HL = Y LL = Y
4: TL = Y HL = N LL = N
5: TL = Y HL = N LL = Y
6: TL = Y HL = Y LL = N
7: TL = Y HL = Y LL = Y
Note: Parameter L5-01 needs to be set to "1" and program L5-03 needs
to be set to the applicable time.
Setting
Factory
Range
Setting
0.0 to
0.0
6000.0
(system
(system
units P1-
units P1-
02)
02)
0.0 to
0.0 Hz
120.0
0.0 to
0.0 min
3600.0
0.0 to
1.0 sec
6000.0
0.0 to
0.0 Hz
120.0
0.0 to
1.0 sec
6000.0
0 to 7
0
YASKAWA TM.iQp.02 iQpump Drive Programming Manual
Menu
Page
Location
No.
Pump Quick
158
Setup
Pump Quick
163
Setup
Pump Quick
164
Setup
Pump Quick
164
Setup
Pump Quick
165
Setup
Pump Quick
165
Setup
Pump Quick
165
Setup
Hide quick links:
Advertisement
