YASKAWA iQpump Series Programming Manual page 206

Factory Default Settings
The following tables detail the factory default settings for the parameters that are affected by the setting of parameter o2-04.
Factory
Drive Model
Nominal Default
CIMR-P7U-
Hp
-107
b8-04
20P4 0.5/0.75 288.2
20P7 2 223.7
21P5 1.5/2 169.4
22P2 3 156.8
23P7 5 122.9
25P5 7.5 94.75
27P5 10 72.69
2011 15 70.44
2015 20 63.13
2018 25 57.87
2022 30 51.79
2030 40 46.27
2037 50 38.16
2045 60 35.78
2055 75 31.35
2075 75/100 23.10
2090 125 20.65
2110 150 18.12
Note: b8-04 = Energy Savings Coefficient
C6-02 = Carrier Frequency
E2-01 = Motor Rated Current
E2-03 = Motor No-Load Current
E2-05 = Motor Line-to-Line Resistance
L2-02 = Momentary Power Loss Ride-Thru Time
L2-03 = Momentary Power Loss Minimum Base Block Time
L2-04 = Momentary Power Loss Voltage Recovery Ramp Time
L8-02 = Overheat Pre-Alarm Level
L8-06 = Input Phase Loss Detection Level
206
Table 35 208/240 VAC Drives
Factory
Factory
Default
Default
for
for for
C6-02
E2-01
<0032>
10 kHz 1.9
10 kHz 3.3
10 kHz 6.2
8 kHz 8.5
10 kHz 14.0
15 kHz 19.6
15 kHz 26.6
8 kHz 39.7
10 kHz 53.0
10 kHz 65.8
10 kHz 77.2
10 kHz 105.0
5 kHz 131.0
5 kHz 160.0
8 kHz 190.0
2 kHz 260.0
2 kHz 260.0
2 kHz 260.0
Factory Factory Factory
Default Default Default
for for for
E2-03 E2-05 L2-02
1.2 9.842 0.1
1.8 5.156 0.1
2.8 1.997 0.2
3.0 1.601 0.3
4.5 0.771 0.5
5.1 0.399 1.0
8.0 0.288 1.0
11.2 0.230 1.0
15.2 0.138 2.0
15.7 0.101 2.0
18.5 0.079 2.0
21.9 0.064 2.0
38.2 0.039 2.0
44.0 0.030 2.0
45.6 0.022 2.0
72.0 0.023 2.0
72.0 0.023 2.0
72.0 0.023 2.0
Factory Factory Factory
Default Default Default
for for for
L2-03 L2-04 L8-02
0.1 0.3 95× C
0.2 0.3 95× C
0.3 0.3 95× C
0.4 0.3 100 × C
0.5 0.3 95× C
0.6 0.3 95× C
0.7 0.3 95× C
0.8 0.3 95× C
0.9 0.3 90× C
1.0 0.6 100× C
1.0 0.6 90× C
1.1 0.6 90× C
1.1 0.6 95× C
1.2 0.6 100× C
1.2 0.1 105× C
1.3 0.1 110× C
1.5 0.1 100× C
1.7 0.1 95× C
YASKAWA TM.iQp.02 iQpump Drive Programming Manual
Factory
Default
for
L8-06
5
7.5
10
12
12
10
17
21
17
15
24
20
18
20
17
16
18
20