GE MM3 Instruction Manual page 219

Numerics
2-SPEED STARTER .............................. 9-6, 9-8, 9-9, 9-10
2-WIRE CONTROL .................................................... 4-21
A
A1 DATA ..................................................................... 5-3
A2 STATUS ................................................................. 5-5
A3 INPUTS .................................................................. 5-9
A4 STATISTICS ......................................................... 5-11
ACCELERATION TIME
actual values ............................................................. 5-4
alarm ...................................................................... 4-15
trip .......................................................................... 4-15
ACCESSORIES ........................................................... 1-3
ACTUAL VALUES
alarm data ................................................................. 5-6
counters .................................................................. 5-12
messages ....................................................5-1, 5-2, 5-3
motor data ................................................................. 5-3
motor identification .................................................... 4-4
motor status .............................................................. 5-8
process data ............................................................. 5-4
timers ..................................................................... 5-11
trip data .................................................................... 5-5
ACTUAL VALUES KEY ................................................ 3-3
ACTUAL VALUES PAGES
A1 DATA ................................................................... 5-3
A2 STATUS ............................................................... 5-5
A3 STATUS ............................................................... 5-9
A4 STATISTICS ...................................................... 5-11
ALARM DATA .............................................................. 5-6
ALARM RESET .......................................................... 4-14
ANALOG ALARM
high delay ............................................................... 4-25
high level ................................................................ 4-25
low delay ................................................................. 4-25
low level .................................................................. 4-24
ANALOG INPUT SIMULATION ................................... 4-43
ANALOG INPUTS ........................................................ C-2
maximum scale ....................................................... 4-24
minimum scale ........................................................ 4-24
overview ................................................................... 2-4
setpoints ................................................................. 4-24
ANALOG OUTPUT SIMULATION ................................ 4-42
ANALOG TRIP
high delay ............................................................... 4-25
high level ................................................................ 4-25
high override ........................................................... 4-25
low delay ................................................................. 4-25
low level .................................................................. 4-25
low override ............................................................ 4-25
APPLICATIONS ......................................................... 6-13
ASYMMETRICAL CURRENT ........................................ D-1
AUTOTRANSFORMER .... 9-19, 9-21, 9-22, 9-23, 9-25, 9-26
AUX 1/2 RELAY CONFIG ........................................... 4-28
AUX 2 COIL ................................................................. 2-5
AUXILIARY CONTACTS
configuration ........................................................... 4-28
contactor status ......................................................... 2-6
GE Power Management
INDEX
B
BAUD RATE ........................................................ 4-3, 8-12
BLOCK DIAGRAM ....................................................... 1-2
BOOT PROGRAM VERSION .......................................4-33
BRIGHTNESS ............................................................. 4-8
BROADCAST COMMAND ...........................................6-14
C
CAUSE OF TRIP ......................................................... 5-5
CERTIFICATION ......................................................... 1-5
CHANGE COMMAND MODE ON ALARM ...................... 4-7
CHANGE OVER CURRENT .......................................... 4-4
CHANGE OVER TIME .................................................. 4-4
CHASSIS MOUNT UNITS ............................................8-12
CLEAR ENERGY USED ............................................... 4-8
CLEAR INTERLOCK COUNTER ................................... 4-8
CLEAR START/TRIP COUNTERS ................................ 4-8
CLEAR TIMERS .......................................................... 4-8
COMMISIONING .......................................................... A-1
COMMUNICATIONS
error checking ........................................................... 6-2
failure setpoints ......................................................... 4-7
MM3PC ....................................................................8-12
Modbus ..................................................................... 6-1
RS485 ............................................................... 2-5, C-1
serial port ................................................................. 2-5
setpoints ................................................................... 4-3
specifications ............................................................ 1-5
COMMUNICATIONS ADDRESS ................................... 4-3
COMPLIANCE ............................................................. 1-5
CONTACTOR INSPECTION ........................................4-31
CONTACTOR SEQUENCE ........................................... 4-5
CONTACTOR STATUS ................................................ 2-6
CONTACTOR STATUS FEEDBACK .............................. C-2
CONTACTS
specifications ............................................................ 1-5
CONTROL SCHEMES
three wire hand / three wire auto ...............................10-8
three wire hand / two wire auto .................................10-6
two wire ................................................................. 10-10
two wire hand / two wire auto ........................... 10-3, 10-4
COUNTERS ...................................................... 4-32, 5-12
CRC-16 ALGORITHM .................................................. 6-3
CT INPUTS
ground fault ............................................................... 2-4
phase CT inputs ........................................................ 2-4
setpoints ................................................................... 4-6
CT ISOLATION ............................................................ E-1
CT SATURATION ........................................................ E-1
CT SIZE ...................................................................... E-1
CT/VT INPUTS ............................................................ 4-6
CTs
excitation curves ....................................................... E-2
isolation .................................................................... E-1
saturation .................................................................. E-1
size .......................................................................... E-1
CURRENT SIMULATION .............................................4-41
CURRENT-VOLTAGE PHASE DIFFERENCE ................ D-1
MM3 Motor Manager 3
i