Siemens SIPROTEC 7SJ62 Instruction Manual page 482

Appendix
Addr. Setting Title
2202 2nd HARMONIC
2203 CROSS BLOCK
2204 CROSS BLK TIMER
2205 I Max
3101 Sens. Gnd Fault
3102 CT Err. I1
3103 CT Err. F1
3104 CT Err. I2
3105 CT Err. F2
3106 VPH MIN
3107 VPH MAX
3109 64-1 VGND
3110 64-1 VGND
3111 T-DELAY Pickup
3112 64-1 DELAY
3113 50Ns-2 PICKUP
3114 50Ns-2 DELAY
3115 67Ns-2 DIRECT.
3117 50Ns-1 PICKUP
3118 50Ns-1 DELAY
3119 51Ns PICKUP
3120 51Ns TIME DIAL
3122 67Ns-1 DIRECT.
3123 RELEASE DIRECT.
3124 PHI CORRECTION
3125 MEAS. METHOD
3126 RESET DELAY
3130 PU CRITERIA
3131 M.of PU TD
A-22
Setting Options
10..45 % 15 %
NO NO
YES
0.00..180.00 sec 0.00 sec
1.50..125.00 A 37.50 A
OFF OFF
ON
Alarm Only
0.003..1.600 A 0.050 A
0.0..5.0 ° 0.0 °
0.003..1.600 A 1.000 A
0.0..5.0 ° 0.0 °
10..100 V 40 V
10..100 V 75 V
1.8..130.0 V 40.0 V
10.0..225.0 V 70.0 V
0.04..320.00 sec 1.00 sec
0.10..40000.00 sec 10.00 sec
0.003..1.500 A 0.300 A
0.00..320.00 sec 1.00 sec
Forward Forward
Reverse
Non-Directional
0.003..1.500 A 0.100 A
0.00..320.00 sec 2.00 sec
0.003..1.400 A 0.100 A
0.10..4.00 sec 1.00 sec
Forward Forward
Reverse
Non-Directional
0.003..1.200 A 0.010 A
-45.0..45.0 ° 0.0 °
COS Phi COS Phi
SIN phi
0..60 sec 1 sec
Vgnd OR INs Vgnd OR INs
Vgnd AND INs
Default Setting
2nd. harmonic in % of fundamental
Cross Block
Cross Block Time
Maximum Current for Inrush Res-
traint
Sensitive Ground Fault
Current I1 for CT Angle Error
CT Angle Error at I1
Current I2 for CT Angle Error
CT Angle Error at I2
L-Gnd Voltage of Faulted Phase Vph
Min
L-Gnd Voltage of Unfaulted Phase
Vph Max
64-1 Ground Displacement Voltage
64-1 Ground Displacement Voltage
Time-DELAY Pickup
64-1 Time Delay
50Ns-2 Pickup
50Ns-2 Time Delay
67Ns-2 Direction
50Ns-1 Pickup
50Ns-1 Time delay
51Ns Pickup
51Ns Time Dial
67Ns-1 Direction
Release directional element
Correction Angle for Dir. Determina-
tion
Measurement method for Direction
Reset Delay
Sensitive Ground Fault PICKUP cri-
teria
Multiples of PU
Comments
Time-Dial
7SJ62 Manual
C53000-G1140-C121-1