AudioCodes Mediant 1000B User Manual page 938

Parameter
Title
title
[GWCDRFormat_Title]
RADIUS Attribute Type
radius-type
[GWCDRFormat_RadiusType]
RADIUS Attribute ID
radius-id
[GWCDRFormat_RadiusID]
User's Manual
Plan; [514] Redirect Number Before Manipulation; [515] Redirect
Number; [526] Redirect Number Type; [527] Redirect Number Plan;
[516] Source Host Name Before Manipulation; [517] Source Host
Name; [518] Destination Host Name Before Manipulation; [519]
Destination Host Name; [520] PSTN Termination Reason; [521]
Module And Port; [522] AOC Currency; [523] AOC Amount; [524]
AOC Multiplier; [525] ISDN Line Type; [600] Channel ID; [601] Coder
Type; [602] Packet Interval; [603] Payload Type; [604] Local Input
Packets; [605] Local Output Packets; [606] Local Input Octets; [607]
Local Output Octets; [608] Local Packet Loss; [609] Local Round
Trip Delay; [610] Local Jitter; [611] Local SSRC Sender; [612]
Remote Input Packets; [613] Remote Output Packets; [614] Remote
Input Octets; [615] Remote Output Octets; [616] Remote Packet
Loss; [617] Remote Round Trip Delay; [618] Remote Jitter; [619]
Remote SSRC Sender; [620] Local RTP IP; [621] Local RTP Port;
[622] Remote RTP IP; [623] Remote RTP Port; [624] RTP IP
DiffServ; [625] Local R Factor; [626] Remote R Factor; [627] Local
MOS CQ; [628] Remote MOS CQ; [629] AMD Decision; [630] AMD
Decision Probability; [631] Latched RTP IP; [632] Latched RTP Port;
[633] Latched T38 IP; [634] Latched T38 Port.
Defines a new name for the CDR field (for Syslog) or for the RADIUS
Attribute prefix name (for RADIUS accounting) that you selected in
the 'Column Type' parameter.
The valid value is a string of up to 31 characters.
You can configure the name to be enclosed by apostrophes (single
or double). For example, if you want the CDR field name to appear
as 'Phone Duration', you must configure the parameter to 'Phone
Duration'. You can also configure the CDR field name with an equals
(=) sign, for example "call-connect-time=".
Note:

For RADIUS Attributes that do not require a prefix name, leave
the parameter undefined.

The parameter's value is case-sensitive. For example, if you want
the CDR field name to be Phone-Duration, you must configure the
parameter to "Phone-Duration" (i.e., upper case "P" and "D").
Defines whether the RADIUS Attribute of the CDR field is a standard
or vendor-specific attribute.

[0] Standard = (Default) For standard RADIUS Attributes.

[1] Vendor Specific = For vendor-specific RADIUS Attributes
(VSA).
Note: The parameter is applicable only for RADIUS accounting (i.e.,
'CDR Type' parameter configured to RADIUS Gateway).
Defines an ID for the RADIUS Attribute. For vendor-specific
Attributes, this represents the VSA ID; for standard attributes, this
represents the Attribute ID (first byte of the Attribute).
The valid value is 0 to 255 (one byte). The default is 0.
Note:

The parameter is applicable only for RADIUS accounting (i.e.,
'CDR Type' parameter configured to RADIUS Gateway).

For VSA's (i.e., 'RADIUS Attribute Type' parameter configured to
Vendor Specific), the parameter must be configured to any value
other than 0.
938
Mediant 1000B Gateway & E-SBC
Description
Document #: LTRT-27055