Table of Contents
Advertisement
USA/Canada section from the products regulatory flyer:
INFORMATION TO THE USER
This document provides regulatory information for the following products:
Wireless Base Station products such as the AP- 600
Base Station products are wireless network products based on IEEE 802.11 standards for wireless LANs as defined and
approved by the Institute of Electrical and Electronics Engineers. Products designed according the IEEE 802.11a standard
use Orthogonal Frequency Division Multiplexing (OFDM) radio technology. Products designed according the
IEEE 802.11b standard use Direct Sequence Spread Spectrum (DSSS) radio technology. These products are designed to
be interoperable with any other wireless product that complies with the corresponding standard.
•
Wireless Fidelity (WiFi) certification is defined by the WECA Wireless Ethernet Compatibility Alliance.
IMPORTANT SAFETY INSTRUCTIONS
When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock and
injury to persons, including the following:
a.
Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
b.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
c.
Do not use this product to report a gas leak in the vicinity of the leak.
Additional Installation Requirements for Base Station products
When installing Base Stations the placement of the device must also satisfy the following installation requirements:
a.
Connect the unit to a grounding type AC wall outlet (100-240 V AC) using only the standard power cord/adapter
provided with the product.
b.
Placement must allow the user to easily disconnect the power cord/adapter of the device from the AC wall-outlet.
c.
Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from
excessive heat and humidity and keep the device free from vibration and dust.
d.
Installation must at all times conform to local regulations.
e.
Always disconnect the cables before opening the equipment enclosure or touching an uninsulated cable, jack or
internal component.
f.
Connections to Base Station products can be made with either Unshielded Twisted Pair (UTP) or Shielded Twisted
Pair cabling (STP) cabling. When using the device in combination with Power over Ethernet, only use Shielded
Twisted Pair cabling (STP).
SAVE THESE INSTRUCTIONS
Wireless LAN and your Health
Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of emitted energy
however is far less than the electromagnetic energy emitted by other wireless devices such as mobile phones, for
example. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and
recommendations, we believe that our Wireless LAN products are safe for use by consumers. These standards and
recommendations reflect the consensus of the scientific community and result from deliberations of panels and
committees of scientists who continually review and interpret the extensive research literature.
Regulatory Information
This device must be installed and used in strict accordance with the manufacturer's instructions as described in the user
documentation that comes with the product.
For country-specific radio approvals or restrictions, please consult section 'Radio Approvals' of this flyer.
In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or
responsible representatives of the organization. For example, these situations may include:
•
Using the wireless equipment on board of airplanes, or
•
In any other environment where the risk of interference to other devices or services is perceived or identified as
harmful.
If you are uncertain of the policy that applies to the use of wireless equipment in a specific organization or environment
(e.g., airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment. The
manufacturer is not responsible for any radio or television interference caused by unauthorized modification of the devices
included with this kit, or the substitution or attachment of connecting cables and equipment other than specified by
manufacturer. The correction of interference caused by such unauthorized modification, substitution or attachment will be
the responsibility of the user. The manufacturer and its authorized resellers or distributors are not liable for any damage or
violation of government regulations that may arise from failing to comply with these guidelines.
Advertisement
Table of Contents
