HEIDENHAIN TNC 640 User Manual page 741

Index
3
3D Touch Probes...................... 492
A
About this manual........................ 4
Adapt rotary coordinate
system..................................... 366
Automatic datum setting.......... 526
At center of 4 holes............. 572
Center of a bolt hole circle... 566
Center of a circular pocket
(hole).................................... 546
Center of a circular stud....... 551
Center of a rectangular
pocket.................................. 538
Center of a rectangular stud 542
In any axis............................ 576
Inside of corner.................... 561
In the touch probe axis........ 570
Outside of corner................. 556
Ridge center........................ 534
Slot center........................... 530
Automatic tool measurement... 722
Axis-specific scaling................. 303
B
Back boring................................ 94
Basic rotation
Measure during program
run........................................ 502
Blank form update.................... 364
Bolt hole circle......................... 207
Bore milling.............................. 106
Boring......................................... 85
C
Centering................................... 79
Circular pocket
Roughing+finishing.............. 164
Circular point patterns.............. 207
Circular slot
Roughing+finishing.............. 174
Circular stud............................. 185
Classification of results............ 587
Compensating workpiece
misalignment............................ 502
By measuring two points on a
straight line.......................... 505
Over two circular studs........ 512
Over two holes.................... 508
Via rotary axis.............. 516, 521
Consideration of basic rotation. 493
Contour cycles......................... 216
Contour train............ 237, 241, 246
Coordinate transformation........ 290
COUPLING INTERPOLATION
HEIDENHAIN | User's manual for cycle programming | 10/2017
TURNING................................. 333
Cycle.......................................... 58
Calling.................................... 60
Define.................................... 59
Cycles and point tables.............. 76
Cylinder surface
Machine contour.......... 259, 269
Ridge machining.................. 266
Slot machining..................... 262
D
Datum shift.............................. 291
In the program..................... 291
With datum tables............... 292
Drilling............................ 81, 88, 98
Drilling Cycles............................ 78
Dwell time................................ 317
E
Engraving................................. 340
F
Face milling.............................. 346
FCL function.............................. 10
Feature Content Level................ 10
Floor finishing........................... 232
FUNCTION TURNDATA............ 364
Fundamentals of Thread
Milling...................................... 134
G
GEAR HOBBING.............. 476, 483
H
Helical thread drilling/milling..... 147
I
Inside thread milling................. 136
INTERPOLATION TURNING,
CONTOUR FINISHING............. 323
K
Kinematic measurement
Accuracy.............................. 691
Backlash............................... 693
Calibration methods.... 692, 705,
707
Hirth coupling...................... 689
Logging function....
684, 699, 709,
Measuring point selection....
685,
Measuring position selection....
691,
Prerequisites........................ 681
Kinematics grid........................ 710
Kinematics grid.................... 710
Kinematics measurement........ 680
Kinematics Measurement
Measure kinematics..... 686, 700
Kinematics measurement
Save kinematics................... 683
KinematicsOpt.......................... 680
L
Linear point patterns................ 210
M
Machine parameters for 3D touch
probe........................................ 495
Machining pattern...................... 67
Measure angle......................... 592
Measure angle of a plane......... 623
Measure any coordinate........... 617
Measure bolt hole circle........... 620
Measure hole........................... 595
Measure hole inside................. 595
Measure hole outside.............. 600
Measure kinematics................. 686
Preset compensation........... 700
Measurement parameters........ 587
Measurement results in Q
parameters............................... 587
Measure rectangular pocket..... 608
Measure rectangular stud........ 605
Measure the plane angle.......... 623
Measure the slot width............ 611
Measure the width of a
ridge................................. 614, 614
Measuring slot width............... 611
Measuring the width of a ridge 614
Mirroring................................... 298
O
Outside thread milling.............. 151
P
Pattern definition........................ 67
Peck drilling........................ 98, 109
Point patterns........................... 206
Overview............................. 206
Point tables................................ 74
Polygon stud............................ 189
Positioning logic....................... 497
Probing feed rate..................... 496
Program call............................. 318
Via cycle............................... 318
716
R
Reaming..................................... 83
690
Recording measurement results....
585
712
Rectangular pocket
Roughing+finishing.............. 159
Rectangular stud...................... 180
Reference images.................... 657
Reset rotary coordinate
741