Table of Contents
Advertisement
•
Aux Return 1 / 2 Panorama Setting:
Balance for the selected Aux Return, or
isting Setting.
•
Aux Return 1 / 2 Assign to PGM1 / PGM2 /
Choose
PGM3 / PGM4:
Return into any of the four PGM buses, or choose
Retain Existing Setting.
•
Aux 1 / 2 Source ID:
familiar, that's because it's just like the ones you
used earlier to construct Source Profiles and map I/O
to Axia Audio Nodes. Click in the box and select the
audio device that will be providing source audio for
the Aux 1 or Aux 2 Return.
button applies any changes made to
•
Save Changes
the Auxiliary Send Description and returns you to
the Show Profile Settings menu.
•
Back to Show Profile
Profile Settings without saving changes.
Monitor Section Screen
The Monitor Section Data screen captures the Moni-
tor settings found in Element's
Since you're working on a "captured" Show Profile, this
page will, of course, mirror the choices you made when
you set up Element in the beginning of this chapter.
From the Show Profile Settings web page, choose the
Monitor Section Data link (refer to Figure 5-4). You'll
find the page divided into four sections: general options,
Control Room Monitor options, Control Room Head-
phone options, and Studio Monitor options.
General Monitor Options
Lets you decide globally how the
•
TIMER MODE:
onscreen Count Up (event) timer will behave when
this profile is loaded:
»
Choose
to start, stop and reset the timer
Manual
by hand using the controls displayed when the
key is pressed.
Timer Options
»
Choose
Auto-Reset
Trim Pan/
Retain Ex-
to fold the selected Aux
On
If this drop-down box looks
link takes you back to Show
menus.
Monitor Options
and the timer will automat-
©2008 Axia Audio — Rev. 3.0
ically reset to zero and begin counting whenever
a fader is turned
On
»
Choose
Auto-Add
when a fader is turned
when that source is turned
timer will not reset to zero when it is restarted.
•
SHOW TENTHS ON:
down and Count Up timers to show or hide tenths of
a second displays. Choices are:
tenths of a second are hidden on
No Timers:
»
both timers.
tenths are shown only on Count-
»
Down Timers:
down timers.
tenths are shown only on Count Up
Up Timers:
»
timers.
All timers display tenths of a sec-
Both Timers:
»
ond readouts.
Sets the fader behavior globally for
•
FADER MODE:
this Show Profile. Choose from:
: faders are turned on and off manually.
Normal
»
: faders turn on when the fader is
Fader Start
»
raised and off when it is lowered to ∞.
»
Retain Source Setting
behaves as its Source Profile dictates.
•
PREVIEW INTERLOCK MODE:
pressing any fader's
Preview
previously-lit
Preview
moving that source from
tor can assign multiple faders to
ing and holding any lit
other
keys to add or subtract.
Preview
If
is chosen, each
Disable
a press-on, press-off latching switch. Multiple fad-
ers can be assigned to
once; a second push cancels any individual
assignment.
•
SWITCHED METER SOURCE SELECT:
whether the far-right on-screen meter bars will dis-
play levels for the
PROGRAM
source feeding the Control Room Monitors (
.
to have the timer count up
and stop counting
On
In this mode, the
Off.
Allows you to set the Count-
: Each individual fader
If
is chosen,
Enable
key causes any other,
key to be extinguished, re-
The board opera-
Preview.
by push-
Preview
key while pushing
Preview
key works like
Preview
simply by pushing
Preview
Preview
Choose
(PGM-4) bus, the
Moni-
Advertisement
Table of Contents
