Table of Contents
Advertisement
or
, or choose
Active
Bypass
(Only applies to Mic sources.)
ting.
•
NOISE GATE THRESHOLD:
at which the Noise Gate will operate (if set to
). Adjustment range is between 0dB and -50dB,
tive
or
Retain Source Settings
•
COMPRESSOR THRESHOLD:
at which the Compressor will operate (if set to
). Adjustment range is between 0dB and -30dB,
tive
or
Retain Source Settings
•
DE-ESSER THRESHOLD:
which the Compressor will operate (if set to
Adjustment range is between 0dB and -20dB, or
tain Source Settings
•
COMPRESSOR RATIO:
pression that will be applied to the mic audio. Ad-
justment range is between 1:1 and 16:1, or
.
Source Settings
•
DE-ESSER RATIO:
de-esser will remove sibilance from the mic audio.
Adjustment range is between 1:1 and 8:1, or
.
Source Settings
•
NOISE GATE DEPTH:
reduction that will be applied to the mic audio if
the noise gate is set to
Threshold is reached. Adjustment range is between
0dB and -30 dB, or
Retain Source Settings
•
COMPRESSOR MODE:
sor between
and
Freeze
tain Source Settings
•
BACKWARD FEED DIM GAIN:
program audio being fed back to this source will be
dimmed when the source is being talked to using the
feature. Adjustment range is 0dB to -30dB,
Talkback
or
Retain Existing Setting.
•
CHANNEL ON/OFF STATUS:
Retain Source Set-
Determines the point
Ac-
.
Determines the point
Ac-
.
Determines the point at
Active
Re-
.
Sets the amount of com-
Retain
Sets how aggressively the
Retain
Sets the amount of noise
and the Noise Gate
Active
.
Change the voice compres-
modes, or
No Freeze
Re-
.
Set how much the
Allows you to turn
©2008 Axia Audio — Rev. 3.0
fader
or
when the Show Profile is loaded.
On
Off
•
CONTROL LOCK MAP:
of these boxes to keep the board op from changing
the selections for this fader's bus assignments, On/
Off state and fader position.
About Channel Lock and Fader Operation:
Say that your station runs syndicated program-
ming overnight, and you want to eliminate the
possibility that the feed could be inadvertently
disrupted. Choose Lock for the channel the feed
is assigned to, and the channel cannot be turned
off, or bus assignment changed, until the chan-
nel is unlocked.
Note that there is currently no option to allow
presetting the fader gain. When you load a Show
).
Profile which specifies a Locked fader, the gain
value is locked to the position of the fader at the
moment the Show Profile is loaded.
When you Unlock the fader using the Chan-
nel Options menu, the fader will resume work-
ing normally from the current position. You can
move it and lock again in a different position if
you wish.
If the fader has been moved, the first touch af-
ter Unlocking immediately resets the gain to
the fader's current position.
•
GROUP START:
Master, Slave
tied to those displayed in the Show Profile Group
Start Screen; a change made here will apply on the
Group Start Screen, and vice-versa. (For more in-
formation on the Group Start Function, please refer
to the Group Start Screen description later in this
chapter.
•
MOTOR FADER POSITION:
faders can be set to assume a predefined position
when a Show Profile is loaded. Choose
to specify a level to use (from -73 dB to +10 dB),
Use
or
Retain Existing Setting
Place a check mark in any
Specify whether this fader is a
or
This setting is
Independent.
Motorized Element
to disable,
Off
.
Advertisement
Table of Contents
