Clamping Rudder Pedals - Piper Cherokee Six Service Manual

PIPER CHEROKEE SIX SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont)
Figure
Aerofiche
Grid No.
6-2. Nose Gear Installation ..........................
........... 2A16
6-3. Clamping Rudder Pedals in Neutral Position .......... ........
2A18
6-4. Rudder Pedals at Neutral Angle ............................
2A18
6-5. Main Gear Oleo Strut Assembly, Cylinder Housing 65319 ......
2A22
6-6. Main Gear Oleo Strut Assembly, Cylinder Housing 65441 ......
2A23
6-7.
Main Gear Installation ..................................... 2B1
6-8. Nose Wheel Assembly
..................................... 2B4
6-9. Main Wheel Assembly .....................................
2B6
6-9a.
Removal and Installation of Anchor Bolts .................... 2B8
6-10.
Wheel Brake Assembly .................................... 2B10
6-11.
Brake System Installation .................................. 2B12
6-12. Brake Master Cylinder (Hand/Parking Brake) ................ 2B13
6-13.
Toe Brake Installation ..................................... 2B15
6-14.
Brake Cylinder 10-20 (Toe Brake) ........................... 2B17
6-15.
Brake Cylinder 10-27 (Toe Brake) ...........................
2B17
6-15a.
Brake Cylinder 10-30 (Toe Brake) ........................... 2B18
6-15b.
Brake Cylinder 17000 (Toe Brake) ...........................
2B18
6-16.
Bleeding Brake (Gravity) ...................................
2B20
6-17. Bleeding Brake (Pressure) ..................................
2B20
6A-1. Nose Gear Oleo Strut Assembly
............................ 2C12
6A-2. Nose Gear Installation
..................................... 2C14
6A-2a.
Nose Gear Service Tolerances .............................. 2C15
6A-2b.
Main Gear Service Tolerances .............................. 2C 19
6A-2c. Adjustment of Eccentric Bushing ............................
2C24
6A-3.
Nose Gear Adjustment .....................................
2DI
6A-4.
Clamping Rudder Pedals in Neutral Position ................. 2D3
6A-5.
Rudder Pedals at Neutral Angle ............................ 2D3
6A-6.
Nose Gear Doors .........................................
2D4
6A-7.
Main Gear Oleo Strut Assembly ............................
2D7
6A-8.
Main Gear Installation ..................................... 2D13
6A-9. Aligning Main Gear ....................
................... 2D19
6A-10. Adjustment of Nose Gear Down Limit Switch
................ 2D22
6A- 11.
Adjustment of Main Gear Down Limit Switch ................ 2D22
6A-12. Throttle Warning Switches .................................
2D24
6A-13. Nose Wheel Assembly
.....................................
2E2
7-1.
Propeller System Installation (Constant Speed) ................
2E18
7-2. Typical Nicks and Removal Method
......................... 2E18
7-2a. Propeller Installation ......................................
2E19
7-3. Propeller Governor
................. .....................
2E21
7-4. Engine Installation
........................................ 2E23
7-4a. Adjustment of Engine Controls ..............................
2F3
7-5. Carburetor
...... ........................... ......... 2F4
7-6. Magneto Inspection ........................................
2F8
7-7. Impulse Coupling ........................................
2F9
7-8. Magneto Timing Marks ....................................
2F10
7-9. Timing Pointer ............................................
2F10
7-10.
Timing Kit Installed .......................................
2F11
7-11.
Breaker Compartment with Cast Timing Marks ...............
2FII
Revised: 11/4/83
1A6