Piper Cherokee Six Service Manual page 7

PIPER CHEROKEE SIX SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont)
Figure
Aerofiche
Grid No.
7-12.
Removing Spark Plug Frozen to Busing ......................................
2F16
7A-1.
Propeller Installation .............................................
......
.... 2G7
7A-2.
Typical Nicks and Removal Method .........................................
2G8
7A-3.
Propeller Governor ........................................................
2GI I
7A-4.
Engine Installation ........... ...........................
...................
2G14
7A-4a.
Adjustment of Engine Control ..................................
.............
2G16
7A-5.
Schematic Diagram of RSA Fuel Injection System .............................
2G19
7A-6.
Fuel Injector ..............................................................
2G20
7A-7.
Fuel-Air Bleed Nozzle ......................................................
2G22
7A-8.
Contact Points .............................................................
2G2
7A-9.
Rotor Holding Tool Installed ...............................................
2H1
7A-10.
Timing Kit Installed .......................................................
2H1
7A- 11.
Aligning Timing Marks......................
...............................
2H2
7A-12.
Checking Flyweight Clearance of Impulse Coupling ............................
2H3
7A-13.
Engine Timing Marks ......................................................
2H4
7A-14.
Magneto Timing Marks ....................................................
2H5
7A-15.
Removing Spring From Lead Assembly ......................................
2H7
7A-16.
Assembly Tool ............................................................
2H7
7A- 17.
Using Assembly Tool ......................................................
.2H
7A-18.
Measuring Lead Assembly Length ...........................................
H8
7A-19.
Cutting Metallic Braid From End of Lead ....................................
2H9
7A-20.
Unbraiding Metallic Shielding ...............................................
2H9
7A-21.
Forming Shielding Around Ferrule ..........................................
2H10
7A-22.
Ferrule Seating Tool ...................
H................. 10
7A-23.
Needle ...................................................................
10
7A-24.
Measuring Wire From Top of Ferrule .......................................
2H 1
7A-25.
Installing Grommet Over Lead Assemblies ...................................
H
II
7A-26.
Lead Assembly Installed in Grommet ........................................
2H 1
7A-27.
Wire Doubled Over for Installation of Eyelet ..................................
2H
7A-28.
Height of Spring in Distributor Block Tower ..................................
H 13
7A-29.
Timing Light Connected to Magneto .........................................
2H15
7A-30.
Timing Marks on Magneto Rotor ...........................................
2H16
7A-31.
Painted Tooth Centered in Timing Window ...................................
H17
7A-32.
Timing Mark on Rotor Aligned with Pointer ..................................
2H17
7A-33.
Timing Light Connected to Magneto and Breakers .............................
2HIS
7A-34.
Cam End View of Magneto .................................................
2H20
7A-35.
Removing Impulse Coupling ......
.........................
2H21
7A-36.
Checking Flyweight to Stop Pin Clearance ....................................
2H21
7A-37.
Stop Pin Installation Dimension .............................................
2H22
7A-38.
Checking Flyweight Axial Wear with Drill Shank ..............................
2H23
7A-39.
Checking Flyweight Radial Wear With Gauge .................................
2H23
7A-40.
Points of Coupling Body Wear ..............................................
2H24
7A-41.
Acceptable and Deformed Coupling Springs ..................................
2H24
7A-42.
Checking Impulse Coupling for Magnetization ................................
211
7A-43.
Orientation of Spring in Coupling Body .....................................
211
7A-44.
Lifting Inner End of Spring .................................................
212
Revised: 8/3/81
1A7