Piper Cherokee Six Service Manual page 257

PIPER CHEROKEE
SIX SERVICE MANUAL
LIST OF ILLUSTRATIONS
(cont)
Figure
Aerofiche
Grid No.
7-12. Removing Spark Plug Frozen to Busing ......................................
2F16
7A-I. Propeller Installation ..................................
..................
2G7
7A-2.
Typical Nicks and Removal Method .......................................
2G8
7A-3. Propeller Governor
...................................................
2G II
7A-4. Engine Installation .........................................................
2G 14
7A-4a.
Adjustment of Engine Control ...............................................
2G16
7A-5. Schematic Diagram of RSA Fuel Injection System .............................
2G 19
7A-6. Fuel Injector ............................
..................................
2G20
7A-7. Fuel-Air Bleed Nozzle .....................................................
2G22
7A-8.
Contact Points ............................................................
2G23
7A-9. Rotor Holding Tool Installed ...............................................
2H I
7A-10. Timing Kit Installed ....................................................
... 2HI
7A-11.
Aligning Timing Marks .....................................................
2H2
7A-12. Checking Flyweight Clearance of Impulse Coupling ............................
2H3
7A-13. Engine Timing Marks ......................................................
2H4
7A-14. Magneto Timing Marks ....................................................
2H5
7A-15. Removing Spring From Lead Assembly
......................................
2H7
7A- 16. Assembly Tool ............................................................
2H7
7A-17. Using Assembly Tool ......................................................
2H8
7A-18. Measuring Lead Assembly Length ...........................................
2H8
7A-19. Cutting Metallic Braid From End of Lead ....................................
2H9
7A-20. Unbraiding Metallic Shielding ...............................................
2H9
7A-21. Forming Shielding Around Ferrule
..........................................
2H10
7A-22. Ferrule Seating Tool ..........................
.................. .... ...
2H10
7A-23. Needle ...................................................................
2H10
7A-24. Measuring Wire From Top of Ferrule ........................................
2H I I
7A-25. Installing Grommet Over Lead Assemblies ....................................
2H I
7A-26. Lead Assembly Installed in Grommet
........................................
2H11
7A-27. Wire Doubled Over for Installation of Eyelet ...............
.... ............... 2H11
7A-28. Height of Spring in Distributor
Block Tower ..................................
2H 13
7A-29. Timing Light Connected
to Magneto ................. .....................
... 2H 15
7A-30. Timing Marks on Magneto Rotor
................. ..........................
2H 16
7A-31.
Painted Tooth Centered in Timing Window ...................................
2H 17
7A-32. Timing Mark on Rotor Aligned with Pointer .................................
2H 17
7A-33. Timing Light Connected to Magneto and Breakers .............................
2H18
7A-34.
Cam End View of Magneto ................................................
2H20
7A-35. Removing Impulse Coupling
............. ......... ........................
2H21
7A-36. Checking Flyweight to Stop Pin Clearance ....................................
2H21
7A-37. Stop Pin Installation Dimension .............................................
2H22
7A-38. Checking Flyweight Axial Wear with Drill Shank ..............................
2H23
7A-39. Checking Flyweight Radial Wear With Gauge .................................
2H23
7A-40. Points of Coupling Body Wear ........
... ... ..... ...........
................. 2H24
7A-41.
Acceptable and Deformed Coupling Springs ................................
... 2H24
7A-42. Checking Impulse Coupling for Magnetization
................................ 211
7A-43. Orientation of Spring in Coupling Body ......................................
211
7A-44. Lifting Inner End of Spring .................................................
212
2A5