HP 9000 Series 700 Manual page 31

Note The following commands are for HP-UX version 10.30 (with four lan cards; lan0,
lan1, lan2 and lan3):
3 If the log files indicate INITIALIZATION COMPLETE, you can now use the
4 If you are upgrading from a previous release of DTC Manager/UX, reboot each
tail /var/adm/rbootd.log
Sat Jan 1 08:48:46 2000 : STARTUP
Sat Jan 1 08:48:46 2000 : ppa=0 Ether
Sat Jan 1 08:48:46 2000 : lan0: type: Ether NMID = 0
Sat Jan 1 08:48:46 2000 : ppa=1 Ether
Sat Jan 1 08:48:46 2000 : lan1: type: Ether NMID = 1
Sat Jan 1 08:48:46 2000 : ppa=2 Ether
Sat Jan 1 08:48:46 2000 : lan2: type: Ether NMID = 2
Sat Jan 1 08:48:46 2000 : ppa=3 Ether
Sat Jan 1 08:48:46 2000 : lan3: type: Ether NMID = 3
Sat Jan 1 08:48:46 2000 : matched lan0 : ppa 0
Sat Jan 1 08:48:46 2000 : matched lan1 : ppa 1
Sat Jan 1 08:48:46 2000 : matched lan2 : ppa 2
Sat Jan 1 08:48:46 2000 : matched lan3 : ppa 3
Sat Jan 1 08:48:46 2000 : got 4 lan device(s)
Sat Jan 1 08:48:47 2000 : INITIALIZATION COMPLETE
tail /var/opt/dtcmgr/log/dtcnmd.log
Sat Jan 1 08:48:55 2000 : STARTUP
Sat Jan 1 08:48:55 2000 : COUNT : 4
Sat Jan 1 08:48:55 2000 : ppa = 0
Sat Jan 1 08:48:55 2000 : type: Ether 'lan0'; index= 0
Sat Jan 1 08:48:55 2000 : ppa = 1
Sat Jan 1 08:48:55 2000 : type: Ether 'lan1'; index= 1
Sat Jan 1 08:48:55 2000 : ppa = 2
Sat Jan 1 08:48:55 2000 : type: Ether 'lan2'; index= 2
Sat Jan 1 08:48:55 2000 : ppa = 3
Sat Jan 1 08:48:55 2000 : type: Ether 'lan3'; index= 3
Sat Jan 1 08:48:55 2000 : found 4 supported rbootd interface(s):
Sat Jan 1 08:48:55 2000 : nmd_main : got 4 lan devices
Sat Jan 1 08:48:55 2000 : matched lan0 : ppa 0
Sat Jan 1 08:48:55 2000 : matched lan1 : ppa 1
Sat Jan 1 08:48:55 2000 : matched lan2 : ppa 2
Sat Jan 1 08:48:55 2000 : matched lan3 : ppa 3
Sat Jan 1 08:48:56 2000 : INITIALIZATION COMPLETE
These tail commands show you the last few lines of the log files. These log files
report whether the process is running. These log files also contain all the error
messages that might have occurred during start-up and running of the daemons.
DTC Manager/UX commands.
DTC by switching it off and then on (power off/on).
This completes the installation of the DTC Manager/UX. You can now use
DTC Manager/UX commands.
Installing DTC Manager/UX with HP-UX 10.x
3
31