Pre-Adjustment Of A Rear Flexible Mounting; Replacement Of A Rear Arm - CITROËN ID 19 Repair Manual

ID 19
OPERATION No. ID 133 - 1 : Work on Ihe enpine
susfwnsion
Op. ID 133-1
83
49
50
51
52
53
54
55
56
57
58
59
PRE-ADJUSTMENT OF A REAR FLEXIBLE MOUNTING
( cars delivered since July 1959).
Bring the upper face of the lower nut securing the arm to a distance of 98 mm from the face of the flexible mounting
which bears against the steel plate support fixed to the body . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . .
REPLACEMENT OF A REAR ARM
( cars delivered until July 1959).
Removal (see Pl. 25).
f
Jack up the front of the vehicle (jacking stand 2505-T, see Pl. 111) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Left-hand support arm : release the distributor spring.
Right-hand support arm : remove the exhaust manifold screen
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove the upper fixing nut (1) of the arm (2)
on the flexible mounting (13) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Place a covered chain sling round the water pump cover (chain sling 1697-T,
see Pl. 42) and support the engine on
a chainblock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove the screws fixing the rear arm (2) and withdraw the arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . .
Refitting (see Pl. 25).
Place the rear arm (2) in position and tighten the fixing screws (spring washers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engage the spindle (8) in the bore of the arm (2). Lower the engine slightly and engage the spigot of the nut (3) in the
bore in the arm (2). Tighten the upper nut (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Left-hand side : hook on the distributor return spring.
Right-hand side : fit the exhaust manifold screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lower the car to the ground (jacking stand 2505-T,
see Pl. 111). Remove the chain sling 1697-T . . . . . . . . . . . . . . . .
REPLACEMENT OF A REAR ARM
( cars delivered since July 1959).
Proceed in the manner indicated for the replacement of a flexible mounting (see paragraphs 37 and following,
this operation).
TOOLS
21 mm spanner
Jacking stand 25 05 -T
12 mm box spanner
23 mm box spanner
Chain sling 1697-T
14 mm spanner
17 mm spanner and
box spanner
14-17 mm spanners and
box spanners
23 mm box spanner
12 mm box spanner
Jacking stand 25 05 -T