CITROËN ID 19 Repair Manual page 293

ID
19 OPERATION No. ID 45 l-4 : Wovk on
the rear brakes Op.ID 451-4
287
8
9
10
11
12
13
14
15
16
17
REPLACEMENTOFTHEREARBRAKESHOES
Removal (see P1.102).
Jack up the rear of the car (jacking bracket 2505-T, see Pl. 111).
Remove the wing and the wheel.
Remove the brake drum fixing screws. Remove the drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unhook the brake shoe return springs (35) (spring pliers 2110-T, see P1.103) . . . . . . . . . . . . , . . . . . . . . . . . . . . . .
Remove the cups (36) from the thrust springs (37) by turning them through $ turn to release them from the rod.
Hold
the guide pins (38) with the spring pliers 2110-T (see Pl. 103, fig.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn back the locking piece (41)
and remove the nuts from the brake shoe anchor pins (40).
Remove the locking piece (41) and remove the brake shoes together with the eccentric bushes (42).
Remove the eccentric bushes (42) from the brake shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE - In order to ensure balanced braking,
it is essential to replace the brake shoes on both rear wheels at the
same time.
Refitting (see Pl. 102).
Place the eccentric bushes (42) in position on the brake shoes.
Fit the shoes on the brake plate,
the shoe fitted with the longest lining being at the front. Fit the locking piece (41).
Screw on the nuts without tightening them.
Fit the guide pins (38), the thrust springs (37) and the cups (36).
Lock the cups on their rod by turning them through $ turn (hold the guide pins (38)
with the spring pliers 2110-T) . . . .
Attach the brake shoe return springs (35)(spring pliers 2110-T, see Pl. 103) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Centralise the brake shoes (fixture 2115-T, see ~1.106) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fit the brake drum.
Lightly grease the bearing face on the hub.
Tighten the brake drum fixing screws.
Fit the wheel. Lower the car to the ground (jacking bracket 2505-T,
see Pl. 111) and tighten the wheel fixing screws
to 108 to 144 ft.lbs (15 to 20 m.kg).
Fitthe rear wing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOOLS
Jacket bracket 2505-T
Spring pliers 2110-T
Pliers 2110-T
16 mm box spanner
Pliers 2110-T
Pliers 2110-T
Fixture 2115-T
Jacking bracket 2505-T
14 mm box spanner