CITROËN ID 19 Repair Manual page 306

300
T
OPERATION No. ID 453-4
: Replacerrzent of a rear articulatiq brake pipe
.
ID 19
PARTICULAR POINTS
When assembling, wake sure that the pipes are aligned correctly in the cet;tre of the unions in order to avoid damage to the pipes or the union threads
REMOVAL (see Pl. 81).
Jack up the rear of the car (jacking bracket 2505-T, see Pl. 111). Remove the rear wing and the protection panels
(side and lower)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
._
Disconnect (left-hand side) the union (1) from the rear brake feed pipe (2) and from the right-hand brake connecting
pipe (3) (spanner 2221-T or 2219-T, see Pl. 61, fig. 3).
Disconnect (right-hand side) the left-hand brake connecting pipe (3) from the articulating pipe (4). Seal the openings
inthe pipes andunions (see Pl. 89) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unscrew the locknut and remove the screw (5) securing the articulating pipe spindle (6).
Remove the screw (7) securing the bracket on the sidemember rear closing panel.
Release the rear section of the articulating pipe from the c-lip (8) securing it to the rear arm.
Remove the articulating pipe spindle (6) from the rear arrr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disconnect the articulating pipe (4) from the wheel cilmdcr (spanner 2221-T or 2219-T, see Pl. 61, fig. 3). Withdraw
the pipe. Seal the opening in the wheel cylinder (see Pl. 89)
. . . . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REFITTING (see Pl. 81).
Engage the articulating pipe spindle (6) in the arm.
Fit the retaining screw (5) together with its locknut. Tighten the
screw (5)moderately andlockthe nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fit the support (7)
on the sidemember closmg panel.
Tighten the fixing screws (spring washers under the heads). . . . . .
Connect the articulating pipe (4) to the whee' cylinder
Tighten the :inlon moderately (spann-r 2221-T or 2219-T,
see Pl.
61,
fig. 3).
Connect (right-hand side) the left-hand brake connec!:an ".p< (3) to the articulating pipe (4) (spanner 2221-T or 2219-T).
TOOLS
Jacking brackkt 2505-T
8 mm box spanner
Spanner 2219-T or 2221-T
5-8 mm box spanners
Spanner 2219-T or 2221-T
5-8 mm box spanners
8 mm box spanner
Spanner 2219-T or
2221-T