Table of Contents
Advertisement
ID
19
OPERATION
No.
ID
334-O
:
Adjustment
of the gear selector control
Op.
ID
334-O
173
1
4
PARTICULAR
POINTS.
To adjust the control tube:
This tube must be accurately
seated in the centre of the support tube of the selector fork shaft levers.
To
adjust
the ball controls:
In
the neutral position the dimension '<a" should be 17.5 + 0.5 mm between the centre of the rear end piece of the cable and the rear face of the
selector tube.
To adjust the control rod:
In the neutral position the dimension "6" should be 39.5 mqbetween
the underside of the instrument
panel cover and the underside of the selector
lever knob.
ADJUSTMENT.
To
adjust
the
control
tube
(see
Pl.
59
and
60)
:
This
tube
must
be
accurately
seated
in the
centre
of the
support
tube
(5)
of
the
selector
fork
shaft
levers.
a)
Disconnect
the
end
piece
(14)
of the
gear
selector
control
rod
(2)
from
the
lever
(11).
b)
Slacken
the
fixing
nuts
of the
bearing
(4)
and
move
the
bearing
in
the
slots
(34)
in
order
to
obtain
the
correct
height;
the
bearing
(4)
is
provided
with
horizontal
slots
enabling
it
to
be
moved
backwards
and
forwards
. . . . . . .
c)
Tighten
the
fixing
nuts
of the
bearing
(4).
To
adjust
the
ball
controls
(see
Pl.
59
and
60)
:
Screw
up
the
sleeve
(12)
until
a measurement
of
"a"
= 17.5
f
0.5
mm
is
obtained
at
the
selector,
the
support
tube
(5)
of
the
selector
fork
shaft
control
levers
being
in
the
"neutral
position".
Tightenthelocknut(13)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To
adjust
the
change
speed
selector
control
rod
(see
Pl.
59
and
60)
:
a)
Place
the
selector
lever
at
a height
such
that
the
distance
"b"
= 39.3
mm.
Keep
it in
this
position.
b)
Move
the
end
piece
(14)
of
the
control
rod
(2)
so that
the
bore
in
the
socket
is
exactly
opposite
the
hole
in
the
lever
(11)
on
the
control
tube.
c)
Fit
the
coupling
pin
(22)
and
tighten
the
nut
(spring
washer).
To
adjust
the
selector
lever
(see
Pl.
59
and
60)
:
a)
Remove
the
cover
of
the
instrument
panel
and
make
sure
that
the
lever
is
in
the
neutral
position.
b)
Make
sure
that
there
is
a distance
"a"
= 17.5
mm
between
the
centre
of the
pin
(15)
and
the
rear
face
of
the
gear
control
shaft
(32);
if not,
adjust
the
ball
control
(see
paragraph
2,
this
operation).
c)
Check
that
there
is
a measurement
of
"bl'
= 39.5
between
the
underside
of
the
instrumentpanel
cover
and
the
under
side
of
the
knob
of the
selector
lever
(35);
if not,
adjust
the
control
(see
paragraph
3,
this
operation).
d)
Make
sure
that
the
selector
operates
properly.
Fit
the
instrument
panel
cover
and
tighten
the
fixing
screws
(cup
washers
under
the
heads).
TOOLS
12 mm
spanner
and
box
spanner
17-21
mm
spanners
- Quick Links:
- Electrical
- Starter Motor
Hide quick links:
Advertisement
Table of Contents
