Huawei Quidway S6700 series Configuration Manual page 93

Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability
[SwitchD] interface xgigabitethernet 0/0/3
[SwitchD-XGigabitEthernet0/0/3] port link-type trunk
[SwitchD-XGigabitEthernet0/0/3] port trunk allow-pass vlan 2 to 9
[SwitchD-XGigabitEthernet0/0/3] stp disable
[SwitchD-XGigabitEthernet0/0/3] quit
# Configure the primary interface and secondary interface of the transit node on the RRPP major
ring.
[SwitchD] rrpp domain 1
[SwitchD-rrpp-domain-region1] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/2 secondary-port xgigabitethernet 0/0/1 level 0
[SwitchD-rrpp-domain-region1] ring 1 enable
[SwitchD-rrpp-domain-region1] quit
# Configure the common interface and edge interface of the assistant edge node on the RRPP
subring.
[SwitchD] rrpp domain 1
[SwitchD-rrpp-domain-region1] ring 2 node-mode assistant-edge common-port
xgigabitethernet 0/0/2 edge-port xgigabitethernet 0/0/3
[SwitchD-rrpp-domain-region1] ring 2 enable
[SwitchD-rrpp-domain-region1] quit
Step 5 Verify the configuration.
After the configurations are complete and network become stable, run the following commands
to verify the configuration:
l Run the display rrpp brief command on Switch B. The following information is displayed:
l Run the display rrpp verbose domain command on Switch B. The following information
Issue 01 (2011-07-15)
[SwitchB] display rrpp brief
Abbreviations for Switch Node Mode :
M - Master , T - Transit , E - Edge , A - Assistant-Edge
RRPP Protocol Status:
RRPP Working Mode: HW
RRPP Linkup Delay Timer: 0 sec (0 sec default).
Number of RRPP Domains: 1
Domain Index : 1
Control VLAN : major 10
Protected VLAN : Reference Instance 1
Hello Timer : 1 sec(default is 1 sec)
Ring Ring Node
ID Level Mode
------------------------------------------------------------------------------
1 0 M
You can find that RRPP is enabled on Switch B. The main control VLAN is VLAN 10, and
the sub control VLAN is VLAN 11. Switch B is the master node of the major ring, with
XGE 0/0/1 as the primary interface and XGE 0/0/2 as the secondary interface.
is displayed:
[SwitchB] display rrpp verbose domain 1
Domain Index : 1
Control VLAN : major 10
Protected VLAN : Reference Instance 1
Hello Timer : 1 sec(default is 1 sec)
RRPP Ring : 1
Ring Level : 0
Node Mode : Master
Ring State : Completed
Is Enabled : Enable
Primary port : XGigabitEthernet0/0/1
Secondary port: XGigabitEthernet0/0/2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Enable
sub 11
Fail Timer : 6 sec(default is 6 sec)
Primary/Common
Port
XGigabitEthernet0/0/1
sub 11
Fail Timer : 6 sec(default is 6 sec)
Is Active : Yes
3 RRPP Configuration
Secondary/Edge
Port
XGigabitEthernet0/0/2
Port status: UP
Port status: BLOCKED
Is
Enabled
Yes
83