Huawei Quidway S6700 series Configuration Manual page 90

Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability
Procedure
Step 1 Configure Switch B as the master node of the major ring.
# Create data VLANs 2 to 9 on Switch B.
<Quidway> system-view
[Quidway] sysname SwitchB
[SwitchB] vlan batch 2 to 9
Configure instance 1, and map it to the VLANs allowed by the RRPP interfaces and protected
VLANs.
[SwitchB] stp region-configuration
[SwitchB-mst-region] instance 1 vlan 2 to 11
[SwitchB-mst-region] active region-configuration
[SwitchB-mst-region] quit
# On SwitchB, configure domain 1. Then configure VLAN 10 as the main control VLAN and
instance 1 as the protected instance of domain 1.
[SwitchB] rrpp enable
[SwitchB] rrpp domain 1
[SwitchB-rrpp-domain-region1] control-vlan 10
[SwitchB-rrpp-domain-region1] protected-vlan reference-instance 1
[SwitchB-rrpp-domain-region1] quit
# Disable STP on the interfaces to be added to the RRPP rings, configure the interfaces as trunk
interfaces, and configure the interfaces to allow service packets of VLAN 2 to VLAN 9 to pass
through.
[SwitchB] interface xgigabitethernet 0/0/1
[SwitchB-XGigabitEthernet0/0/1] port link-type trunk
[SwitchB-XGigabitEthernet0/0/1] port trunk allow-pass vlan 2 to 9
[SwitchB-XGigabitEthernet0/0/1] stp disable
[SwitchB-XGigabitEthernet0/0/1] quit
[SwitchB] interface xgigabitethernet 0/0/2
[SwitchB-XGigabitEthernet0/0/2] port link-type trunk
[SwitchB-XGigabitEthernet0/0/2] port trunk allow-pass vlan 2 to 9
[SwitchB-XGigabitEthernet0/0/2] stp disable
[SwitchB-XGigabitEthernet0/0/2] quit
# Configure the primary interface and secondary interface of the master node on the RRPP major
ring.
[SwitchB] rrpp domain 1
[SwitchB-rrpp-domain-region1] ring 1 node-mode master primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[SwitchB-rrpp-domain-region1] ring 1 enable
[SwitchB-rrpp-domain-region1] quit
Step 2 Configure Switch C as the master node of the subring.
# Create data VLANs 2 to 9 on Switch C.
<Quidway> system-view
[Quidway] sysname SwitchC
[SwitchC] vlan batch 2 to 9
Configure instance 1, and map it to the VLANs allowed by the RRPP interfaces and protected
VLANs.
[SwitchC] stp region-configuration
[SwitchC-mst-region] instance 1 vlan 2 to 11
[SwitchC-mst-region] active region-configuration
[SwitchC-mst-region] quit
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 RRPP Configuration
80