Harmonic ProView 2900 Installation Manual page 77

Chapter 5: Operation and Management
OSD 1 / OSD 2 (if applicable) -
•
OSD parameter status will be available in future software versions.
Video 1 (and Video 2)
5.4.4.1.
The Video 1 Menus (and Video 2 in dual decoder IRDs) display video parameter Statuses. To
access the Video 1 menu in the front panel control interface go to Status Video Video 1.
The following screen displays the Video 1 menu:
1 Standard Format 1 Standard Format
1 Standard Format 1 Standard Format
2 Frame Rate 2 Frame Rate 2 Frame Rate 2 Frame Rate
3 Chroma Format 3 Chroma Format
3 Chroma Format 3 Chroma Format
4 Resolution 4 Resolution 4 Resolution 4 Resolution
5 Aspect Ratio 5 Aspect Ratio
5 Aspect Ratio 5 Aspect Ratio
6 Field Sequence 6 Field Sequence 6 Field Sequence 6 Field Sequence
7 Picture Coding Type 7 Picture Coding Type
7 Picture Coding Type 7 Picture Coding Type
8 Bit Rate e e e 8 Bit Rat 8 Bit Rat 8 Bit Rat
9 VBV Buffer Size 9 VBV Buffer Size 9 VBV Buffer Size 9 VBV Buffer Size
10 Decoding Errors 10 Decoding Errors 10 Decoding Errors 10 Decoding Errors
NOTE
The "Decoding Errors" parameter indicates the video stream health.
The available information is:
Standard Format – Indicates the number of lines in the incoming video. In this example,
•
625 lines indicate PAL video format.
Frame Rate – Displays the frame rate of the incoming video stream
•
Chroma Format – Displays the Chroma format currently used for the incoming video
•
stream
Resolution – Displays the horizontal and vertical video resolutions for the incoming video
•
stream (for example, the number of pixels per horizontal and vertical screen lines)
Aspect Ratio – Displays the aspect ratio for the incoming video stream
•
Field Sequence – Displays the type of field sequence found in the decoded service.
•
There are two available values: Normal, and 3:2 Pulldown
Picture Coding Type – displays the types of picture coding that were found in the
•
decoded service. Available picture coding types are: I-B-P, I-P, P-B and P Only.
Bit Rate – Displays the bit rate, in bits/sec, for the incoming video stream
•
VBV Buffer Size – Displays the VBV buffer size
•
Decoding Errors – Displays the total number of decoding errors
•
VBI 1 (and VBI 2)
5.4.4.2.
The VBI 1 Menu (and VBI 2 in dual decoder IRD's) display VBI parameters Status. To access
the VBI 1 Menu in the front panel control interface go to Status Video Vbi 1.
The following screen displays the VBI 1 menu:
© Harmonic Inc. Manual p/n 101543/Ver 1.0
Video 1 Video 1 Video 1 Video 1
5-23
ProView 2900 Status Menu
1 1 1 1 - - - - 3 3 3 3 - - - - 4 4 4 4 - - - - 1 1 1 1
625 [Ln] 625 [Ln]
625 [Ln] 625 [Ln]
25 [Hz] 25 [Hz] 25 [Hz] 25 [Hz]
4:2:0 4:2:0
4:2:0 4:2:0
H:720 * V:608 8 8 8 H:720 * V:60 H:720 * V:60 H:720 * V:60
4:3
4:3
NORMAL NORMAL NORMAL NORMAL
P P P P - - - - B B B B
11080800 [Bps]e 11080800 [Bps]e 11080800 [Bps]e 11080800 [Bps]e
04096000 [Bit] 04096000 [Bit] 04096000 [Bit] 04096000 [Bit]
000000 000000 000000 000000
ProView 2900 Series/SW Version 1.94
4:3
4:3