Table of Contents
Advertisement
Chapter 6: Receiver Configuration Modules
Physical Link
6.3.1.1.
The physical Link menu is used for enabling the operation of the physical link (the MPEGoIP
IN1 interface in this example), as well as for configuring its parameters.
01 Operation
01 Operation
01 Operation
01 Operation
02 IP Address
02 IP Address
02 IP Address
02 IP Address
03 Subnet Mask
03 Subnet Mask
03 Subnet Mask
03 Subnet Mask
04 Default Gateway
04 Default Gateway
04 Default Gateway
04 Default Gateway
Available options are:
Operation - for enabling or disabling this port
•
IP Address – for setting this MPEGoIP input port's IP address
•
Subnet Mask - for setting this MPEGoIP input port's Subnet Mask
•
Default Gateway - for setting the default gateway address
•
NOTES
The operator must enter valid IP addresses before the ProView 2900 can operate. If one or
more IP addresses are not entered correctly, the following message is desplayed: "Front-End
Warning – IP Configuration Error". This message remains until all IP addresses are
entered correctly.
Both MPEGoIP input ports must use the same gateway.
Logical Source (socket)
6.3.1.2.
The Logical Source menu is used for configuring the connection with the end device ("logical
port").
01 IP Address Type
01 IP Address Type
01 IP Address Type
01 IP Address Type
02 IP Multicast Address
02 IP Multicast Address
02 IP Multicast Address
02 IP Multicast Address
03 UDP Destination Port
03 UDP Destination Port
03 UDP Destination Port
03 UDP Destination Port
The available options are:
IP Address Type - for choosing between Multicast and Unicast address types
•
MULTICAST – for selecting Multicast IP address type. When selected, the IP
Multicast address menu is displayed, which enables configuring the Multicast
address. An IGMP Join request is sent for connecting with the IP Multicast
address that was configured. The ProView 2900 filters the relevant transport
stream with the configured Multicast IP address and UDP port.
UNICAST - for selecting Unicast IP address type. The ProView 2900 filters the
relevant transport stream only by the configured UDP port.
IP Multicast Address - for setting the logical port's IP address (this menu is displayed
•
only when Multicast IP address type is selected)
UDP Destination Port – for setting the logical port's UDP port from which to receive data
•
© Harmonic Inc. Manual p/n 101543/Ver 1.0
Physical Link
Physical Link
Physical Link
Physical Link
Logical Source
Logical Source
Logical Source
Logical Source
6-31
IP Receiver Configuration
1 1 1 1 - - - - 2 2 2 2 - - - - 1 1 1 1 - - - - 1 1 1 1 - - - - 1 1 1 1
DISABLE
DISABLE
DISABLE
DISABLE
010.006.000.196
010.006.000.196
010.006.000.196
010.006.000.196
2 2 2 2 55.255.255.000
55.255.255.000
55.255.255.000
55.255.255.000
010.006.000.001
010.006.000.001
010.006.000.001
010.006.000.001
1 1 1 1 - - - - 2 2 2 2 - - - - 1 1 1 1 - - - - 1 1 1 1 - - - - 2 2 2 2
MULTICAST
MULTICAST
MULTICAST
MULTICAST
224.010.010.010
224.010.010.010
224.010.010.010
224.010.010.010
02000
02000
02000
02000
ProView 2900 Series/SW Version 1.94
Hide quick links:
Advertisement
Table of Contents
