Changing Source Names In The Display Window - Yamaha RX-V1800 Owner's Manual

5
Press and hold the button you want to
program on the other remote control until
"OK" appears in the display window
(@)
on
the remote control.
""NG" appears in the display \vindow
(@)
on the
remote control if learning was unsuccessful. In this
case, start over from step 4.
Remote control features
Changing source names in the
display window
You can change the name of the input source that appears
in the display window
(@)
on the remote control if you
want to use a different name from the factory preset. This
feature is useful when you have set an input area to control
a different component.
0
00 000,
o
0 0 0
0:
00
Q
Other remote control
1
Set the operation mode selector to @AMP or
@SOURCE and then press an input selector
button (CD) or u to select the input area you
want to rename.
The name of the selected input area appears in the
display window
(@).
AMP
~
(~)
r
1
• If you want to program another function. repeat steps 4
and 5.
• If you continuously want to program another function for
another component. press
@SELECT fj, / \j
to select the
component. and then repeat steps 4 and 5.
or
SOIHO OVO PHONO
6
Press @LEARN again to exit from the
learning mode.
Notes
• "ERROR" appears in the display window
(@)
on the remote
control if you press a button no1 indicated in the respective step.
or when you press more than one button simultaneously.
• This remote control can learn approximately 200 functions.
However. depending on the signals learned. "FULL" may
appear in the display before you program 200 functions. In this
case. clear unnecessary programmed functions to make room
for further learning.
• Learning may not he possihle in the following cases:
- when the batteries in the remote control for this unit or other
components are weak.
when the distance hetween the two remote controls is too
great or too small.
- when the remote control infrared windows are not facing each
other at the appropriate angle.
- when the remote control is exposed to direct sunlight.
- when the function to be programmed is continuous or
uncommon.
2
Press @RENAME using a ballpoint pen or
similar object.
Note
If you do not complete each of the following steps within 30
seconds. the renaming mode will be automatically canceled.
In this case. start over from step 2.
105
En
5
Press and hold the button you want to
program on the other remote control until
"OK" appears in the display window
(@)
on
the remote control.
""NG" appears in the display \vindow
(@)
on the
remote control if learning was unsuccessful. In this
case, start over from step 4.
Remote control features
Changing source names in the
display window
You can change the name of the input source that appears
in the display window
(@)
on the remote control if you
want to use a different name from the factory preset. This
feature is useful when you have set an input area to control
a different component.
0
00 000,
o
0 0 0
0:
00
Q
Other remote control
1
Set the operation mode selector to @AMP or
@SOURCE and then press an input selector
button (CD) or u to select the input area you
want to rename.
The name of the selected input area appears in the
display window
(@).
AMP
~
(~)
r
1
• If you want to program another function. repeat steps 4
and 5.
• If you continuously want to program another function for
another component. press
@SELECT fj, / \j
to select the
component. and then repeat steps 4 and 5.
or
SOIHO OVO PHONO
6
Press @LEARN again to exit from the
learning mode.
Notes
• "ERROR" appears in the display window
(@)
on the remote
control if you press a button no1 indicated in the respective step.
or when you press more than one button simultaneously.
• This remote control can learn approximately 200 functions.
However. depending on the signals learned. "FULL" may
appear in the display before you program 200 functions. In this
case. clear unnecessary programmed functions to make room
for further learning.
• Learning may not he possihle in the following cases:
- when the batteries in the remote control for this unit or other
components are weak.
when the distance hetween the two remote controls is too
great or too small.
- when the remote control infrared windows are not facing each
other at the appropriate angle.
- when the remote control is exposed to direct sunlight.
- when the function to be programmed is continuous or
uncommon.
2
Press @RENAME using a ballpoint pen or
similar object.
Note
If you do not complete each of the following steps within 30
seconds. the renaming mode will be automatically canceled.
In this case. start over from step 2.
105
En