Yamaha RX-V1800 Owner's Manual page 107

1
Set the operation mo,de selector to
@SOURCE and then press an input selector
button (CD) or
u
to
sE~lect
the input area you
want to set up.
Remote control features
4
Press the numeric buttons (@) to enter the
four-digit remote control code for the
component you want to use.
For a complete list of available remote control codes,
refer to "List of remote control codes" at the end of
this manual.
AMP
ff
b
SOURCE
-)
~
V-AUXIDOCK
9
o
ENT
6
Press @LEARN again to exit from the setup
mode.
2
Press and hold @LE,ARN for about 3
seconds using a ballpoint pen or similar
object.
The library name (e.g.
L~DVDI)
and the name of the
selected input area (e.g..DVD) appear alternately in
the display window
(@)
on the remote control.
!
~\cil-:.
• You can set a remote control code of a di fferent type of
component to an input area. Press
@<J /
C>
repeatedly to
change the library (component category).
Library choices: L:DVD, L:DVR, L:LD, L:CD, L;CDR,
L:MD, L:TAP (tape), L:TUN (tuner),
L:AMP, L:TV, L:CAB (cable),
L:SAT (satellite), L:VCR
• If you want to setup for another input area, press the input
selector button
(CD)
or
U.
or press
@SELECT
~
/
V
repeatedly to select the input area.
5
7
Press @ENTER to set the number.
"OK" appears in the display window
(@)
on the
remote control if setting is successful.
"NG" appears in the display window
(@)
on the
remote control if the setting is unsuccessful. In this
case, start over fron1 step 3.
~\cil-:.
If you continuously want to set up another code for another
component. press the input selector button
(CD)
or
u '
or
@SELECT
~
/
V
repeatedly to select the component. then
repeat steps 2 through
.5.
Press
®C>
(play) or AV POWER to confirm
whether you can control your component
using the remote control.
or
Notes
• Be sure to press and hold
@ LEARN
for at least 3
seconds, otherwise the learning process will start.
• If you do not complete each of the following steps within
30 seconds, the setting mode will be automatically
canceled. In this case, start over from step 2.
3
Press @ ENTER.
The four-digit code set for the selected component
appears in the display wjndow
(@).
Note
"0000" appears in the display window
(@)
if no code has
been set.
If operation is not possible and the manufacturer of your
component has more than one code, try each of them unti I
you find the correct one.
Notes
• "ERROR" appears in the display window
(@)
on the remote
control if you press a button not indicated in the respective step,
or when you press more than one button simultaneously.
• The supplied remote control does not contain all possible codes
for commercially available audio and video components
(including Yamaha components). If operation is not possible
with any of the remote control codes, program the new remote
control function using the learn feature (see "Programming
codes from other remote controls" on page
1(4)
or use the
remote control supplied with the component.
• Functions programmed w,ing the learn feature take priority over
remote control code functions.
103
En
1
Set the operation mo,de selector to
@SOURCE and then press an input selector
button (CD) or
u
to
sE~lect
the input area you
want to set up.
Remote control features
4
Press the numeric buttons (@) to enter the
four-digit remote control code for the
component you want to use.
For a complete list of available remote control codes,
refer to "List of remote control codes" at the end of
this manual.
AMP
ff
b
SOURCE
-)
~
V-AUXIDOCK
9
o
ENT
6
Press @LEARN again to exit from the setup
mode.
2
Press and hold @LE,ARN for about 3
seconds using a ballpoint pen or similar
object.
The library name (e.g.
L~DVDI)
and the name of the
selected input area (e.g..DVD) appear alternately in
the display window
(@)
on the remote control.
!
~\cil-:.
• You can set a remote control code of a di fferent type of
component to an input area. Press
@<J /
C>
repeatedly to
change the library (component category).
Library choices: L:DVD, L:DVR, L:LD, L:CD, L;CDR,
L:MD, L:TAP (tape), L:TUN (tuner),
L:AMP, L:TV, L:CAB (cable),
L:SAT (satellite), L:VCR
• If you want to setup for another input area, press the input
selector button
(CD)
or
U.
or press
@SELECT
~
/
V
repeatedly to select the input area.
5
7
Press @ENTER to set the number.
"OK" appears in the display window
(@)
on the
remote control if setting is successful.
"NG" appears in the display window
(@)
on the
remote control if the setting is unsuccessful. In this
case, start over fron1 step 3.
~\cil-:.
If you continuously want to set up another code for another
component. press the input selector button
(CD)
or
u '
or
@SELECT
~
/
V
repeatedly to select the component. then
repeat steps 2 through
.5.
Press
®C>
(play) or AV POWER to confirm
whether you can control your component
using the remote control.
or
Notes
• Be sure to press and hold
@ LEARN
for at least 3
seconds, otherwise the learning process will start.
• If you do not complete each of the following steps within
30 seconds, the setting mode will be automatically
canceled. In this case, start over from step 2.
3
Press @ ENTER.
The four-digit code set for the selected component
appears in the display wjndow
(@).
Note
"0000" appears in the display window
(@)
if no code has
been set.
If operation is not possible and the manufacturer of your
component has more than one code, try each of them unti I
you find the correct one.
Notes
• "ERROR" appears in the display window
(@)
on the remote
control if you press a button not indicated in the respective step,
or when you press more than one button simultaneously.
• The supplied remote control does not contain all possible codes
for commercially available audio and video components
(including Yamaha components). If operation is not possible
with any of the remote control codes, program the new remote
control function using the learn feature (see "Programming
codes from other remote controls" on page
1(4)
or use the
remote control supplied with the component.
• Functions programmed w,ing the learn feature take priority over
remote control code functions.
103
En