Yamaha RX-V1800 Owner's Manual page 114

Remote control features
• Clearing a macro function
You can clear the function programmed for a certain
macro button.
1
Set the operation mode selector to @AMP or
@SOURCE and then press @MACRO using
a ballpoint pen or similar object.
....MCR '1" appears in the display window
(@)
on the
remote control.
2
Press @LEARN using a ballpoint pen or
similar object.
....LEARN" and the selected component name
(e.g ..... DVD") appear alternately in the display
window.
. . . . . . . . . . .01 . . . . . ,4 . . . .
• • • • • I I •
• • • I · ' • • . •
.............
I · · • • • • • • • • . • •
I · • • • • • • •
....... ,. .... , "III" ,
" · 1
!
Notes
• Do not press and hold @LEARN. If you hold it down for
more than 3 seconds. the remote control enters the remote
control code setting mode.
• If you do not complete each of the following steps within
30 seconds. the learning mode will he automatically
canceled. In this case. start over from step 2.
Note
or
....
M~C?
+
3
Press and hold @CLEAR using a ballpoint
pen or similar object and then press the
button you want to clear for about 3 seconds.
....C;OK" appears in the display window
(@)
if
clearing was successful. Once ....C;OK" appears in the
display window on the remote control, release the
ballpoint pen or similar object used to press
@CLEAR
to exit from the clearing mode. The
remote control returns to the learning mode.
~\cil:
• If you continuously want to clear another function. repeat
step 3.
• If you continuously want to clear another function for
another component. press @5ELECT
!J. / V
to select the
input area. then repeat step 3.
• Once you clear a learned function. the hutton reverts to the
factory setting (or to the manufacturer setting if you have
set remote control codes).
4
Press @LEARN again to exit.
Notes
• "C:NG" appears in the display window
(@)
on the remote
control if clearing was unsuccessful. In this case. start over from
step 2.
• "ERROR" appears in the display window
(@)
if you press
more than one hutton simultaneously.
110
En
If you do not complete each of the following steps within 30
seconds. the macro programming mode will be
automatically canceled. In this case. start over from step I.
2
Press and hold @CLEAR using a ballpoint
pen or similar object, then press the macro
button you want to clear for about 3 seconds.
....C;OK" appears in the display window (@) on the
remote control if clearing was successful.
'-...../ '-...../ "-../
llVD BlllHDDVD
~
~\cil:
• If you continuously want to clear another function. repeat
step 2.
• Once you clear a programmed function. the button reverts
to the factory setting (or to the manufacturer setting if you
have set remote control codes).
3
Press @MACRO again to exit from the
macro programming mode.
Notes
• "C:NG" appears in the display window
(@)
on the remote
control if clearing was unsuccessful. In this case. start over from
step 2.
• "ERROR" appears in the display window
(@)
on the remote
control if you press more than one hutton simultaneously.
Remote control features
• Clearing a macro function
You can clear the function programmed for a certain
macro button.
1
Set the operation mode selector to @AMP or
@SOURCE and then press @MACRO using
a ballpoint pen or similar object.
....MCR '1" appears in the display window
(@)
on the
remote control.
2
Press @LEARN using a ballpoint pen or
similar object.
....LEARN" and the selected component name
(e.g ..... DVD") appear alternately in the display
window.
. . . . . . . . . . .01 . . . . . ,4 . . . .
• • • • • I I •
• • • I · ' • • . •
.............
I · · • • • • • • • • . • •
I · • • • • • • •
....... ,. .... , "III" ,
" · 1
!
Notes
• Do not press and hold @LEARN. If you hold it down for
more than 3 seconds. the remote control enters the remote
control code setting mode.
• If you do not complete each of the following steps within
30 seconds. the learning mode will he automatically
canceled. In this case. start over from step 2.
Note
or
....
M~C?
+
3
Press and hold @CLEAR using a ballpoint
pen or similar object and then press the
button you want to clear for about 3 seconds.
....C;OK" appears in the display window
(@)
if
clearing was successful. Once ....C;OK" appears in the
display window on the remote control, release the
ballpoint pen or similar object used to press
@CLEAR
to exit from the clearing mode. The
remote control returns to the learning mode.
~\cil:
• If you continuously want to clear another function. repeat
step 3.
• If you continuously want to clear another function for
another component. press @5ELECT
!J. / V
to select the
input area. then repeat step 3.
• Once you clear a learned function. the hutton reverts to the
factory setting (or to the manufacturer setting if you have
set remote control codes).
4
Press @LEARN again to exit.
Notes
• "C:NG" appears in the display window
(@)
on the remote
control if clearing was unsuccessful. In this case. start over from
step 2.
• "ERROR" appears in the display window
(@)
if you press
more than one hutton simultaneously.
110
En
If you do not complete each of the following steps within 30
seconds. the macro programming mode will be
automatically canceled. In this case. start over from step I.
2
Press and hold @CLEAR using a ballpoint
pen or similar object, then press the macro
button you want to clear for about 3 seconds.
....C;OK" appears in the display window (@) on the
remote control if clearing was successful.
'-...../ '-...../ "-../
llVD BlllHDDVD
~
~\cil:
• If you continuously want to clear another function. repeat
step 2.
• Once you clear a programmed function. the button reverts
to the factory setting (or to the manufacturer setting if you
have set remote control codes).
3
Press @MACRO again to exit from the
macro programming mode.
Notes
• "C:NG" appears in the display window
(@)
on the remote
control if clearing was unsuccessful. In this case. start over from
step 2.
• "ERROR" appears in the display window
(@)
on the remote
control if you press more than one hutton simultaneously.