Optimizing The Speaker Setting For Your Listening Room; Using Auto Setup - Yamaha RX-V1800 Owner's Manual

Optimizin the speaker setting for your listening room
This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment.
Using AUTO· SETllP
Notes
• Be advised that it is normal for loud lest tones to be output
during the "AUTO SETUP" procedure.
• To achieve the best results. make sure the room is as quiet as
possible while the "AUTO SETUP" procedure is in progress. If
there is too much ambient noise. the results may not be
satisfactory.
• We recommend that you get out of the room while this unit is in
the automatic setup procedure. Keep quiet when you leave the
room.
It
takes approximately 3 minutes for this unit to complete
the automatic setup procedure.
~\ci{-:.
• The initial setting for each parameter is indicated in bold.
• Before performing operations. set the operation mode selector
on the remote control to
@AI\I1P.
• Basic procedure olf the automatic setup
1
Make sure of the following check points
before starting the
~~UTO
SETUP operations.
D Speakers are connected appropriately.
D Headphones are disconnected from this unit.
D This unit and the video nl0nitor are turned on.
D
The connected subwoofer is turned on and the volume
level is set to about half way (or slightly less).
D The crossover frequency controls of the
connected subwoofer is set to the maximum.
D If you use the external arnplifiers (see page 29),
the amplifiers are turned on and the settings are
appropriate.
D The room is sufficiently quiet.
2
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
"MIC ON" and "View ()SD 1\1enu" appears in the
front panel display.
@
L " " ' " ' '
~_c-o-:nni-directional
~~:J
microphone
The following menu screen appears on the video
monitor.
You can also run "AUTO SETUP" using the system menu
that appears in the front panel display. When you connect
the optimizer microphone to the OPTIMIZER MIC jack. the
following display appears in the front panel display. This
manual uses the OSD illustrations to explain the "AUTO
SETUP" procedure.
3
Place the optimizer microphone at your
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
Optimizer microphone
It
is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would
be when you are seated in your listening position. You can
use the attached screw of a tripod (etc.) to fix the optimizer
microphone to the tripod (etc.).
37
En
Optimizin the speaker setting for your listening room
This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment.
Using AUTO· SETllP
Notes
• Be advised that it is normal for loud lest tones to be output
during the "AUTO SETUP" procedure.
• To achieve the best results. make sure the room is as quiet as
possible while the "AUTO SETUP" procedure is in progress. If
there is too much ambient noise. the results may not be
satisfactory.
• We recommend that you get out of the room while this unit is in
the automatic setup procedure. Keep quiet when you leave the
room.
It
takes approximately 3 minutes for this unit to complete
the automatic setup procedure.
~\ci{-:.
• The initial setting for each parameter is indicated in bold.
• Before performing operations. set the operation mode selector
on the remote control to
@AI\I1P.
• Basic procedure olf the automatic setup
1
Make sure of the following check points
before starting the
~~UTO
SETUP operations.
D Speakers are connected appropriately.
D Headphones are disconnected from this unit.
D This unit and the video nl0nitor are turned on.
D
The connected subwoofer is turned on and the volume
level is set to about half way (or slightly less).
D The crossover frequency controls of the
connected subwoofer is set to the maximum.
D If you use the external arnplifiers (see page 29),
the amplifiers are turned on and the settings are
appropriate.
D The room is sufficiently quiet.
2
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
"MIC ON" and "View ()SD 1\1enu" appears in the
front panel display.
@
L " " ' " ' '
~_c-o-:nni-directional
~~:J
microphone
The following menu screen appears on the video
monitor.
You can also run "AUTO SETUP" using the system menu
that appears in the front panel display. When you connect
the optimizer microphone to the OPTIMIZER MIC jack. the
following display appears in the front panel display. This
manual uses the OSD illustrations to explain the "AUTO
SETUP" procedure.
3
Place the optimizer microphone at your
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
Optimizer microphone
It
is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would
be when you are seated in your listening position. You can
use the attached screw of a tripod (etc.) to fix the optimizer
microphone to the tripod (etc.).
37
En