Yamaha RX-V1800 Owner's Manual page 119

Using multi-zone configuration
• Using Zone 2/Zone 3 remote control
(except Europe model)
You can control Zone 2 or Zone 3 features by using the supplied Zone 2/Zone 3 ren10te control. First, set the ID 1/ID2
switch and ZONE 2/Z0NE 3 switch appropriately.
Note
Controlling the amplifier 1function
o
XM
Selects XM as the input source of the controlling zone.
f) Input selector buttons
Selects the desired input source for the controlling zone.
C) 101/102 switch
Switches the remote controlll) betvveen ID 1 and ID2 (see
page 118).
C!) POWER
Turns on Zone 2 or Zone 3.
Note
This button is operational only when @MASTER ON/OFF on
the front panel is pressed inward to the ON position.
G
STANDBY
Sets Zone 2 or Zone 3 to the standby mode.
This button is operational only when @MASTER ON/OFF on
the front panel is pressed inward to the ON position.
~
VOLUME +1-
Increases or decreases the volume level of Zone 2 or Zone
3.
~
MUTE
Mutes the sound of Zone 2 or Zone 3. Press again to
restore the audio output to the previous volun1e level.
4D
ZONE 2/Z0NE 3 switch
Switches between the operation mode of Zone 2 and that
of Zone 3.
Controlling the tuner function (see page 54)
Select "TUNER" as the input source of the controlling zone
to use the following functions
8
PRESET
~/V
Selects one of the 8 preset station numbers (1 to 8) when
the colon (:) is displayed in the front panel display (see
page 56).
e
AlBICIOIE
Selects one of the preset station groups (A to E) (see
page 55).
Controlling the XM Satellite Radio tuning
function (see page 58)
Select "XM" as the input source of the controlling zone to use
the following functions.
f) Numeric buttons
(All Channel Search or Category Search mode)
Use 1 to 9 and 0 to enter a channel number directly.
(Preset Search mode)
Use 1 to 8 to enter a preset channel number directly.
While holding down 0NUMBER (see page
116). press the
numeric buttons to enter the desired channel numbers directly
when this unit is in the All Channel Search or Category Search
mode.
8
A-E/CAT.
<J
II>
(All Channel Search mode)
Changes the channel category.
(Category Search mode)
Changes the channel category.
(Preset Search mode)
Changes the preset channel group (A to E).
Continued
115
En
Using multi-zone configuration
• Using Zone 2/Zone 3 remote control
(except Europe model)
You can control Zone 2 or Zone 3 features by using the supplied Zone 2/Zone 3 ren10te control. First, set the ID 1/ID2
switch and ZONE 2/Z0NE 3 switch appropriately.
Note
Controlling the amplifier 1function
o
XM
Selects XM as the input source of the controlling zone.
f) Input selector buttons
Selects the desired input source for the controlling zone.
C) 101/102 switch
Switches the remote controlll) betvveen ID 1 and ID2 (see
page 118).
C!) POWER
Turns on Zone 2 or Zone 3.
Note
This button is operational only when @MASTER ON/OFF on
the front panel is pressed inward to the ON position.
G
STANDBY
Sets Zone 2 or Zone 3 to the standby mode.
This button is operational only when @MASTER ON/OFF on
the front panel is pressed inward to the ON position.
~
VOLUME +1-
Increases or decreases the volume level of Zone 2 or Zone
3.
~
MUTE
Mutes the sound of Zone 2 or Zone 3. Press again to
restore the audio output to the previous volun1e level.
4D
ZONE 2/Z0NE 3 switch
Switches between the operation mode of Zone 2 and that
of Zone 3.
Controlling the tuner function (see page 54)
Select "TUNER" as the input source of the controlling zone
to use the following functions
8
PRESET
~/V
Selects one of the 8 preset station numbers (1 to 8) when
the colon (:) is displayed in the front panel display (see
page 56).
e
AlBICIOIE
Selects one of the preset station groups (A to E) (see
page 55).
Controlling the XM Satellite Radio tuning
function (see page 58)
Select "XM" as the input source of the controlling zone to use
the following functions.
f) Numeric buttons
(All Channel Search or Category Search mode)
Use 1 to 9 and 0 to enter a channel number directly.
(Preset Search mode)
Use 1 to 8 to enter a preset channel number directly.
While holding down 0NUMBER (see page
116). press the
numeric buttons to enter the desired channel numbers directly
when this unit is in the All Channel Search or Category Search
mode.
8
A-E/CAT.
<J
II>
(All Channel Search mode)
Changes the channel category.
(Category Search mode)
Changes the channel category.
(Preset Search mode)
Changes the preset channel group (A to E).
Continued
115
En