Clearing Configurations - Yamaha RX-V1800 Owner's Manual

Clearingconfigulalions
You can clear all changes made in each function set, such
as learned functions, macros, renarned input area names
and setup remote control codes.
• Clearing function sets
1
Set the operation mode selector to @AMP or
@SOURCE and then press @CLEAR by
using a ballpoint pen or similar object.
"CLEAR" appears in the display window
(@).
or
Note
If you do not complete each of the following steps within 30
seconds. the clearing mode will be automatically canceled.
In this case. start over from step I.
2
Press @ fj. I
V
to select the clear mode.
L:CD (etc.) (L: Name of an input area)
Clears all learned functions in the respective
input area. The name of a component is shown
after a semicolon (:). Press an input selector
button to select the input area.
L:AMP Clears all learned functions for controlling the
amplifier functions of this unit.
L:ALL Clears all learned functions.
M:ALL Clears all programmed macros.
RNAME Clears all renamed source names.
FCTRY Clears all remole functions and returns the
remote to the factory settings.
Remote control features
3
Press and hold @CLEAR again for about 3
seconds.
"WAIT" appears in the display window
(@).
If
clearing was successful, "C;OK" appears in the
display window
(@)
on the remote control.
~'¥-:.
Once you have cleared a learned function for a button. the
button reverts to the factory setting (or to the manufacturer
setting if you have set remote control codes).
Notes
• "L:ALL" and "FCTRY" may take about 30 seconds to
complete.
• "C:NG" appears in the display window
(@)
if clearing
was unsuccessful. In this case start over from step 2.
• "ERROR" appears in the display window
(@)
if you press
a button not indicated in the respective step. or if you press
more than one button simultaneously.
4
Press @CLEAR again to exit.
• Clearing a learned function
You can clear the function learned for a certain button in
each control area.
1
Set the operation mode selector to @AMP or
@SOURCE and then press an input selector
button (CD) or
~
to select the input area
containing the function you want to clear.
The selected component name appears in the display
window.
AMP
~
~ " - " . - _ . ~ _ : ;
t
cg)
TV
(9)
TUNER
or
SOIHO OVO PHONO
109
En
Clearingconfigulalions
You can clear all changes made in each function set, such
as learned functions, macros, renarned input area names
and setup remote control codes.
• Clearing function sets
1
Set the operation mode selector to @AMP or
@SOURCE and then press @CLEAR by
using a ballpoint pen or similar object.
"CLEAR" appears in the display window
(@).
or
Note
If you do not complete each of the following steps within 30
seconds. the clearing mode will be automatically canceled.
In this case. start over from step I.
2
Press @ fj. I
V
to select the clear mode.
L:CD (etc.) (L: Name of an input area)
Clears all learned functions in the respective
input area. The name of a component is shown
after a semicolon (:). Press an input selector
button to select the input area.
L:AMP Clears all learned functions for controlling the
amplifier functions of this unit.
L:ALL Clears all learned functions.
M:ALL Clears all programmed macros.
RNAME Clears all renamed source names.
FCTRY Clears all remole functions and returns the
remote to the factory settings.
Remote control features
3
Press and hold @CLEAR again for about 3
seconds.
"WAIT" appears in the display window
(@).
If
clearing was successful, "C;OK" appears in the
display window
(@)
on the remote control.
~'¥-:.
Once you have cleared a learned function for a button. the
button reverts to the factory setting (or to the manufacturer
setting if you have set remote control codes).
Notes
• "L:ALL" and "FCTRY" may take about 30 seconds to
complete.
• "C:NG" appears in the display window
(@)
if clearing
was unsuccessful. In this case start over from step 2.
• "ERROR" appears in the display window
(@)
if you press
a button not indicated in the respective step. or if you press
more than one button simultaneously.
4
Press @CLEAR again to exit.
• Clearing a learned function
You can clear the function learned for a certain button in
each control area.
1
Set the operation mode selector to @AMP or
@SOURCE and then press an input selector
button (CD) or
~
to select the input area
containing the function you want to clear.
The selected component name appears in the display
window.
AMP
~
~ " - " . - _ . ~ _ : ;
t
cg)
TV
(9)
TUNER
or
SOIHO OVO PHONO
109
En