Selecting Decoders - Yamaha RX-V1800 Owner's Manual

Advanced sound configurations
("2ch Stereo" only)
C:T'
1. . . .
[i.)
EI. . . .
~:::;L.. I....E:I.)EI... .
~:::; I:;~~ 1. . . .
EI.)[ l . ..
~::;E: l...E:I.)EI... .
F'l... 1 . . . . [:
I.)
E
1....
r"'!":~
1....[:1.)[1....
("7ch Stereo" only)
[:I:::'FEC:'T LEi.)EI....
("Straight Enhancer" and
("7ch Enhancer" only)
Selecting decoders
2-channel stereo direct. Bypasses the decoders and DSP processors of this unit for pure hi-fl stereo
sound when playing 2-channel analog sources.
Choices: AUTO, OFF
• Select "AUTO" to bypass the decoders, DSP processors and the tone control circuitry only when
"BASS" and "TREBLE" are set to 0 dB (see page 52).
• Select "OFF' not to bypass the decoders, DSP processors and the tone control circuitry when
"BASS" and "TREBLE" are set to 0 dB.
• When multi-channel signals are input, they are downl11ixed to 2 channels and output from the front
left and right speakers.
• The low-frequency signals of the front left and right channels are redirected to the subwoofer in the
following cases:
- "LFE/BASS OUT" is set to "BOTH" (see page 80).
- "FRONT SP" is set to "SMALL" (see page 80) and "LFE/BASS OUT" is set to "SWFR" (see
page 80).
7-channel stereo center, surround left, surround right, surround back, presence left and presence right
levels. Adjusts the volume level of each channel in the 7-channel stereo mode.
Control range:
0
to
100(1<
Straight and 7-channel Compressed Music Enhancer effect level. The high-frequency signals of some
sources may be emphasized too much. In this case, set the effect level to "LOW".
Choices:
HIGH,
LOW
• Select "HIGH" for a high effect level.
• Select "LOW" for a low effect level.
• Selecting decoders for 2-channel
sources (surround decode mode)
Use this feature to play back sources with selected
decoders. You can play back 2-channel sources on multi-
channels.
Set the operation mode selector to @AMP and
then press @SUR. DECODE repeatedly on the
remote control to select the surround decode
mode.
You can select the desired surround decoder mode
depending on the type of source you are playing and your
personal preference.
~\cil~
You can change the decoder parameter settings. Press
@) PARAMETER and then @
6.
I
V
repeatedly on the remote
control to select the desired decoder parameter. You can change
the value or the selected parameter by pressing
@<I I
[>
repeatedly on the remote control.
72
En
Advanced sound configurations
("2ch Stereo" only)
C:T'
1. . . .
[i.)
EI. . . .
~:::;L.. I....E:I.)EI... .
~:::; I:;~~ 1. . . .
EI.)[ l . ..
~::;E: l...E:I.)EI... .
F'l... 1 . . . . [:
I.)
E
1....
r"'!":~
1....[:1.)[1....
("7ch Stereo" only)
[:I:::'FEC:'T LEi.)EI....
("Straight Enhancer" and
("7ch Enhancer" only)
Selecting decoders
2-channel stereo direct. Bypasses the decoders and DSP processors of this unit for pure hi-fl stereo
sound when playing 2-channel analog sources.
Choices: AUTO, OFF
• Select "AUTO" to bypass the decoders, DSP processors and the tone control circuitry only when
"BASS" and "TREBLE" are set to 0 dB (see page 52).
• Select "OFF' not to bypass the decoders, DSP processors and the tone control circuitry when
"BASS" and "TREBLE" are set to 0 dB.
• When multi-channel signals are input, they are downl11ixed to 2 channels and output from the front
left and right speakers.
• The low-frequency signals of the front left and right channels are redirected to the subwoofer in the
following cases:
- "LFE/BASS OUT" is set to "BOTH" (see page 80).
- "FRONT SP" is set to "SMALL" (see page 80) and "LFE/BASS OUT" is set to "SWFR" (see
page 80).
7-channel stereo center, surround left, surround right, surround back, presence left and presence right
levels. Adjusts the volume level of each channel in the 7-channel stereo mode.
Control range:
0
to
100(1<
Straight and 7-channel Compressed Music Enhancer effect level. The high-frequency signals of some
sources may be emphasized too much. In this case, set the effect level to "LOW".
Choices:
HIGH,
LOW
• Select "HIGH" for a high effect level.
• Select "LOW" for a low effect level.
• Selecting decoders for 2-channel
sources (surround decode mode)
Use this feature to play back sources with selected
decoders. You can play back 2-channel sources on multi-
channels.
Set the operation mode selector to @AMP and
then press @SUR. DECODE repeatedly on the
remote control to select the surround decode
mode.
You can select the desired surround decoder mode
depending on the type of source you are playing and your
personal preference.
~\cil~
You can change the decoder parameter settings. Press
@) PARAMETER and then @
6.
I
V
repeatedly on the remote
control to select the desired decoder parameter. You can change
the value or the selected parameter by pressing
@<I I
[>
repeatedly on the remote control.
72
En