Macro Programming Features - Yamaha RX-V1800 Owner's Manual

Remote control features
3
Press @
L/
' V
to select and enter a character.
Pressing
@
' V
changes the character as follows:
A to Z, 1 to 9,0,
+
(plus), - (hyphen), ; (semicolon),
/ (slash), and space.
Pressing
@
L
changes the characters in reverse order.
~
, ~ .lI1 ....
"l.
....41 ...
Macro programming features
The macro programming feature makes it possible to
perform a series of operations with the press of a single
button. For example, when you want to playa CD,
normall y you would turn on the components, select the
CD input, and press the play button to start playback. The
macro programming feature lets you perform all of these
operations simply by pressing the CD macro button. The
buttons listed as macro buttons below are factory set with
macro programs. You can also program your own macros
(see page 108).
• MACRO operations
4
Press @e> to move the cursor to the next
position.
Macro buttons
MACRO ON/OFF
MACRO
,"
~(j)~
Press @<J to move the cursor to the previous position.
5
Press @ENTER to set the new name.
"OK" appears in the display window
(@)
on the
renlote control if renaming was successful.
"NG" appears in the display window (@) on the
remote control if renaming was unsuccessful.
In
this
case, start over from step 3.
If you continuously want to rename another input area. press
the input selector hutton
(CD)
or
u .
or press @SELECT
6. /
\j repeatedly to select the component. then repeat steps .3
through 5.
6
Press @RENAME again to exit from the
renaming mode.
1
Set the @ MACRO ON/OFF selector to ON.
@YAMAHA
2
Press the desired macro button.
3
Set the @ MACRO ON/OFF selector to OFF
when you finish to using the macro
programming operation.
@YAMAHA
REV
10. 'l .ll .
I.' ••••..••
• • ' 1 ' • • •
I . ' · •••• 11 I I ••••
..... ...
.....
• • 1 · 1 • • . . • •
, "l .......
" 1 , ..... .ll1:"1" ' .....
Notes
Note
"ERROR" appears in the display window
(@)
on the remote
control if you press a button not indicated in the respective step.
or when you press more than one button simultaneously.
106
En
• While the remote control is running a macro program. it does
not accept any other operation until it has completed running
the program (the transmission indicator stops flashing).
• Continue to aim the remote control at the component the macro
is operating until the macro operation is complete.
Remote control features
3
Press @
L/
' V
to select and enter a character.
Pressing
@
' V
changes the character as follows:
A to Z, 1 to 9,0,
+
(plus), - (hyphen), ; (semicolon),
/ (slash), and space.
Pressing
@
L
changes the characters in reverse order.
~
, ~ .lI1 ....
"l.
....41 ...
Macro programming features
The macro programming feature makes it possible to
perform a series of operations with the press of a single
button. For example, when you want to playa CD,
normall y you would turn on the components, select the
CD input, and press the play button to start playback. The
macro programming feature lets you perform all of these
operations simply by pressing the CD macro button. The
buttons listed as macro buttons below are factory set with
macro programs. You can also program your own macros
(see page 108).
• MACRO operations
4
Press @e> to move the cursor to the next
position.
Macro buttons
MACRO ON/OFF
MACRO
,"
~(j)~
Press @<J to move the cursor to the previous position.
5
Press @ENTER to set the new name.
"OK" appears in the display window
(@)
on the
renlote control if renaming was successful.
"NG" appears in the display window (@) on the
remote control if renaming was unsuccessful.
In
this
case, start over from step 3.
If you continuously want to rename another input area. press
the input selector hutton
(CD)
or
u .
or press @SELECT
6. /
\j repeatedly to select the component. then repeat steps .3
through 5.
6
Press @RENAME again to exit from the
renaming mode.
1
Set the @ MACRO ON/OFF selector to ON.
@YAMAHA
2
Press the desired macro button.
3
Set the @ MACRO ON/OFF selector to OFF
when you finish to using the macro
programming operation.
@YAMAHA
REV
10. 'l .ll .
I.' ••••..••
• • ' 1 ' • • •
I . ' · •••• 11 I I ••••
..... ...
.....
• • 1 · 1 • • . . • •
, "l .......
" 1 , ..... .ll1:"1" ' .....
Notes
Note
"ERROR" appears in the display window
(@)
on the remote
control if you press a button not indicated in the respective step.
or when you press more than one button simultaneously.
106
En
• While the remote control is running a macro program. it does
not accept any other operation until it has completed running
the program (the transmission indicator stops flashing).
• Continue to aim the remote control at the component the macro
is operating until the macro operation is complete.