Setting remote control TUNER 10
1
Set the operation mode selector to @AMP or
@SOURCE and then press CDTUNER on the
remote control to select the tuner to change
the remote control IDI.
2
Press and hold @LEARNI for about 3
seconds using a ballpoint: pen or similar
object until "L;TUN" and "TUNER"
alternately appear in the display window (@).
3 seconds
Notes
• Be sure to press and hold
(~LEt~RN
for at least J
seconds. otherwise the learning process will start.
• If you do not complete each of the following steps within
J()
seconds. the setting mode will be automatically
canceled. In this case. start over from step 2.
3
Press @ ENTER.
The four-digit code set for the selected input area
appears in the display window
(@)
on the remote
control.
4
Press the numeric bUittons (@) to enter the
four-digit remote control code for the input
area you want to use"
Advanced setup
6
Press @LEARN again to exit from the setup
mode.
•
Remote control
XM 10
I:;~:C:
>: : 1 ' = ' 1 I [)
(U.S.A. and Canada models only)
Use this feature to set the XM ID of this unit for remote
control recognition.
Choices: 101, ID2
• Select "ID I" when the remote control XM ID library
code is set to "2604".
•
Select "ID2" when the remote control XM ID library
code is set to "2605".
Setting remote control XM 10
1
Set the operation mode selector to @AMP or
@SOURCE and then press CDXM on the
remote control to select the XM to change the
remote control 10.
2
Press and hold @LEARN for about 3
seconds using a ballpoint pen or similar
object until "L;TUN" and "XM" alternately
appear in the display window (@) on the
remote control.
3 seconds
2602
Operates this unit lIsing the
(initial setting)
default code.
IOI
(initial setting)
Notes
• Be sure to press and hold
@
LEARN
for at least
J
seconds. otherwise thc learning process will start.
• If you do not completc each of the following steps within
JO seconds. the setting mode will be automatically
canceled. In this case. start over from stcp 2.
5
Press @ ENTER to Sf~t the number.
"OK" appears in the display window
(@)
if the
setting was successful.
"NG" appears in the display window
(@)
if the
setting was unsuccessful. In this case, start over from
step 2.
*
I The remote control setting.
*2 The setting of this unit.
260J
Operates this unit lIsing an
alternative code
102
3
Press @ENTER.
The four-digit code set for the selected input area
appears in the display window
(@)
on the remote
control.
119
En
Setting remote control TUNER 10
1
Set the operation mode selector to @AMP or
@SOURCE and then press CDTUNER on the
remote control to select the tuner to change
the remote control IDI.
2
Press and hold @LEARNI for about 3
seconds using a ballpoint: pen or similar
object until "L;TUN" and "TUNER"
alternately appear in the display window (@).
3 seconds
Notes
• Be sure to press and hold
(~LEt~RN
for at least J
seconds. otherwise the learning process will start.
• If you do not complete each of the following steps within
J()
seconds. the setting mode will be automatically
canceled. In this case. start over from step 2.
3
Press @ ENTER.
The four-digit code set for the selected input area
appears in the display window
(@)
on the remote
control.
4
Press the numeric bUittons (@) to enter the
four-digit remote control code for the input
area you want to use"
Advanced setup
6
Press @LEARN again to exit from the setup
mode.
•
Remote control
XM 10
I:;~:C:
>: : 1 ' = ' 1 I [)
(U.S.A. and Canada models only)
Use this feature to set the XM ID of this unit for remote
control recognition.
Choices: 101, ID2
• Select "ID I" when the remote control XM ID library
code is set to "2604".
•
Select "ID2" when the remote control XM ID library
code is set to "2605".
Setting remote control XM 10
1
Set the operation mode selector to @AMP or
@SOURCE and then press CDXM on the
remote control to select the XM to change the
remote control 10.
2
Press and hold @LEARN for about 3
seconds using a ballpoint pen or similar
object until "L;TUN" and "XM" alternately
appear in the display window (@) on the
remote control.
3 seconds
2602
Operates this unit lIsing the
(initial setting)
default code.
IOI
(initial setting)
Notes
• Be sure to press and hold
@
LEARN
for at least
J
seconds. otherwise thc learning process will start.
• If you do not completc each of the following steps within
JO seconds. the setting mode will be automatically
canceled. In this case. start over from stcp 2.
5
Press @ ENTER to Sf~t the number.
"OK" appears in the display window
(@)
if the
setting was successful.
"NG" appears in the display window
(@)
if the
setting was unsuccessful. In this case, start over from
step 2.
*
I The remote control setting.
*2 The setting of this unit.
260J
Operates this unit lIsing an
alternative code
102
3
Press @ENTER.
The four-digit code set for the selected input area
appears in the display window
(@)
on the remote
control.
119
En