Yamaha RX-V1800 Owner's Manual page 118

Using multi-zone configuration
Operate the following operations after activating the Zone 2
or Zone 3 operation mode.
• Adjusting the balance of the speaker
level in Zone 2 or Zone 3
• Adjusting the tonal quality of Zone 2 or
Zone 3
Press @TONE CONTROL repeatedly to select
"BALANCE" and then rotate @PROGRAM on
the front panel to adjust the balance of the front
left and right speaker level of the selected zone.
Set the operation mode selector to @)AMP and
then press CH +/- on the remote control to
adjust the high-frequency response (TREBLE) or
TV VOL +/- to adjust the low-frequency
response (BASS) respectively.
BASS
TREBLE
AMP
~
(Iii)
r
t
Rotate the @INPUT selector on the front panel
(or set the operation mode selector to @)AMP
and then press one of the input selector buttons
on the remote control) to select the input source
of the selected zone.
If the relTIote control is used to select the input source, "2:
name of the selected input source" or "3: name of the
selected input source" is displayed in the display window
(® )
on the remote control when Zone 2 or Zone 3 is
selected respectively.
• Select "TUNER" as the input source to use the FM/AM
tuning features in the selected zone. For details about
the FM/AM tuning operations, see "FM/AM tuning"
on page 54.
• Select ""XM" as the input source to use the XM
Satellite Radio features in the selected zone. For details
about the XM Satellite Radio operations, see "XMT~1
Satellite Radio tuning" on page 58.
• Select "V-AUX" as the input source to play back the
sources in the iPod stationed in a Yamaha iPod
universal dock (such as the YDS-I 0 sold separately) in
the selected zone. You can only control iPod in the
simple remote mode (see page 64).
Note
• Selecting the input source of Zone 2 or
Zone 3
The input sources arc shared across all zones. You cannot select
the same input source in multiple zones simultaneously.
You can also adjust the tonal quality of Zone 2 or Zone 3 hy using
@TONE CONTROL
on the front panel. For details. see
"Adjusting the tonal quality" on page 52.
You must complete this step within 10 seconds while the selected
zone rIashes in the front panel display. Otherwise. the currently
selected zone mode is automatically canceled. In this case. press
®ZONE CONTROLS
on the front panel again.
• Adjusting the volume level of Zone 2 or
Zone 3
Note
Check that "ZONE 2" or "ZONE 3" is displayed in the display
window
(@)
of the remote control before you adjust the tonal
quality of the corresponding zone (see page 113).
Rotate @VOLUME on the front panel (or press
@VOLUME +/- on the remote control) to adjust
the volume level of the selected zone.
~\<il-:.
Press
@MUTE
on the remote control to mute the sound output to
the selected zone.
Note
When you usc the external amplifiers in Zone 2 or Zone 3.
@VOLUME +/-
can he used only when "VOLUME" is set to
"VAR" in "ZONE SET" (sec page 95).
114
En
Using multi-zone configuration
Operate the following operations after activating the Zone 2
or Zone 3 operation mode.
• Adjusting the balance of the speaker
level in Zone 2 or Zone 3
• Adjusting the tonal quality of Zone 2 or
Zone 3
Press @TONE CONTROL repeatedly to select
"BALANCE" and then rotate @PROGRAM on
the front panel to adjust the balance of the front
left and right speaker level of the selected zone.
Set the operation mode selector to @)AMP and
then press CH +/- on the remote control to
adjust the high-frequency response (TREBLE) or
TV VOL +/- to adjust the low-frequency
response (BASS) respectively.
BASS
TREBLE
AMP
~
(Iii)
r
t
Rotate the @INPUT selector on the front panel
(or set the operation mode selector to @)AMP
and then press one of the input selector buttons
on the remote control) to select the input source
of the selected zone.
If the relTIote control is used to select the input source, "2:
name of the selected input source" or "3: name of the
selected input source" is displayed in the display window
(® )
on the remote control when Zone 2 or Zone 3 is
selected respectively.
• Select "TUNER" as the input source to use the FM/AM
tuning features in the selected zone. For details about
the FM/AM tuning operations, see "FM/AM tuning"
on page 54.
• Select ""XM" as the input source to use the XM
Satellite Radio features in the selected zone. For details
about the XM Satellite Radio operations, see "XMT~1
Satellite Radio tuning" on page 58.
• Select "V-AUX" as the input source to play back the
sources in the iPod stationed in a Yamaha iPod
universal dock (such as the YDS-I 0 sold separately) in
the selected zone. You can only control iPod in the
simple remote mode (see page 64).
Note
• Selecting the input source of Zone 2 or
Zone 3
The input sources arc shared across all zones. You cannot select
the same input source in multiple zones simultaneously.
You can also adjust the tonal quality of Zone 2 or Zone 3 hy using
@TONE CONTROL
on the front panel. For details. see
"Adjusting the tonal quality" on page 52.
You must complete this step within 10 seconds while the selected
zone rIashes in the front panel display. Otherwise. the currently
selected zone mode is automatically canceled. In this case. press
®ZONE CONTROLS
on the front panel again.
• Adjusting the volume level of Zone 2 or
Zone 3
Note
Check that "ZONE 2" or "ZONE 3" is displayed in the display
window
(@)
of the remote control before you adjust the tonal
quality of the corresponding zone (see page 113).
Rotate @VOLUME on the front panel (or press
@VOLUME +/- on the remote control) to adjust
the volume level of the selected zone.
~\<il-:.
Press
@MUTE
on the remote control to mute the sound output to
the selected zone.
Note
When you usc the external amplifiers in Zone 2 or Zone 3.
@VOLUME +/-
can he used only when "VOLUME" is set to
"VAR" in "ZONE SET" (sec page 95).
114
En