Yamaha RX-V1800 Owner's Manual page 112

Remote control features
• Programming macro operations
You can program your own macro and use the macro
programming feature to transmit several remote control
commands in sequence at the press of a button. Be sure to
set up remote control codes or perform learning operations
before programming the macro.
Notes
• The default macro is not cleared when a new macro is
programmed for a hutton. The default macro can he used again
when the programmed macro is cleared.
• It is not possihle to add a new signal (macro step) to the default
macro. Programming a macro changes all macro contents.
• We do not recommend programming continuous operations
such as volume control in a macro.
Note
"AGAIN" appears in the display window
(@)
if you press a
hutton other than a macro hutton.
3
Press the buttons for the functions you want
to include in the macro operation in
sequence.
You can set up to 10 steps (10 functions). After you
have set 10 steps, "'FULL" appears and the remote
control automatically exits from the macro mode.
Example:
Set the input source to DVD
~
Activate the DVD
player
~
Set the sleep timer
1
Set the operation mode selector to @AMP or
@SOURCE and then press @MACRO using
a ballpoint pen or similar object.
"'MCR
7"
appears in the display window (@) on the
remote control.
or
AMP
~
S;u='.R . • . C .' . · . • . : .
!
.. t
M7?
+
Step 1 (""MCR 1"): Press DVD.
Step 2 (""MCR 2"): Press AV POWER.
Step 3 ("'MCR 3"): Press SLEEP.
Indicates the
number of macro
steps entered
Note
I
f
you do not complete each of the following steps within 30
seconds. the macro programming mode will he
automatically canceled. In this case. start over from step I.
t
Flashes alternately so you can
set the next step
2
Press the @MACRO button you want to use
to operate the macro.
The macro button name (e.g. "'M;DVD") and the
selected component name (e.g. "'DVD") appear
alternately in the display window (@) on the remote
control.
MDfTAPE
108
En
t
Note
To change the selected input area, press
@5ELECT
f1 / V.
Pressing the input selector buttons will program a macro step.
whereas
@5ELECT
f1 / V
only changes the selected input
area.
4
Press @MACRO again using a ballpoint pen
or similar object when the operation
sequence you want to program is complete.
Note
"ERROR" appears in the display window
(@)
if you press
more than one hutton simultaneously.
Remote control features
• Programming macro operations
You can program your own macro and use the macro
programming feature to transmit several remote control
commands in sequence at the press of a button. Be sure to
set up remote control codes or perform learning operations
before programming the macro.
Notes
• The default macro is not cleared when a new macro is
programmed for a hutton. The default macro can he used again
when the programmed macro is cleared.
• It is not possihle to add a new signal (macro step) to the default
macro. Programming a macro changes all macro contents.
• We do not recommend programming continuous operations
such as volume control in a macro.
Note
"AGAIN" appears in the display window
(@)
if you press a
hutton other than a macro hutton.
3
Press the buttons for the functions you want
to include in the macro operation in
sequence.
You can set up to 10 steps (10 functions). After you
have set 10 steps, "'FULL" appears and the remote
control automatically exits from the macro mode.
Example:
Set the input source to DVD
~
Activate the DVD
player
~
Set the sleep timer
1
Set the operation mode selector to @AMP or
@SOURCE and then press @MACRO using
a ballpoint pen or similar object.
"'MCR
7"
appears in the display window (@) on the
remote control.
or
AMP
~
S;u='.R . • . C .' . · . • . : .
!
.. t
M7?
+
Step 1 (""MCR 1"): Press DVD.
Step 2 (""MCR 2"): Press AV POWER.
Step 3 ("'MCR 3"): Press SLEEP.
Indicates the
number of macro
steps entered
Note
I
f
you do not complete each of the following steps within 30
seconds. the macro programming mode will he
automatically canceled. In this case. start over from step I.
t
Flashes alternately so you can
set the next step
2
Press the @MACRO button you want to use
to operate the macro.
The macro button name (e.g. "'M;DVD") and the
selected component name (e.g. "'DVD") appear
alternately in the display window (@) on the remote
control.
MDfTAPE
108
En
t
Note
To change the selected input area, press
@5ELECT
f1 / V.
Pressing the input selector buttons will program a macro step.
whereas
@5ELECT
f1 / V
only changes the selected input
area.
4
Press @MACRO again using a ballpoint pen
or similar object when the operation
sequence you want to program is complete.
Note
"ERROR" appears in the display window
(@)
if you press
more than one hutton simultaneously.