Setting the speaker impedance
Caution
If you are to use 6 ohm speakers, set '"SPEAKER
IMP." to '"6Q MIN" as follows BEFORE using this
unit. You can also use 4 ohrn speakers as the front
speakers.
Connections
Turninglhis.unit ·.on.·and .011
•
Turning on this unit
Press @MASTER ON/OFF on the front panel
inward to the ON position to turn on this unit.
When you turn on this unit by pressing @MASTER ONI
OFF,
the main zone is turned on.
1
2
Make sure this unit is turned off.
Press and hold @S1
I
RAIGHT on the front
panel and then press @MASTER ON/OFF
inward to the ON position to turn on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
,I,
':-(j)-:'
When you turn on this unit, there will be a delay for a few
seconds before this unit can reproduce sound.
•
Turning off this unit
Press @MASTER ON/OFF on the front panel
again to release it outward to the
OFF
position to
turn off this unit.
Rotate the @PROGllAM selector to select
"SPEAKER IMP.".
3
STRAIGHT
~
While holding
dClwn
....
~
Notes
• @MAIN ZONE ON/OFF
on the front panel as well as
@POWER
and
C1)STANDBY
on the remote control are
operational only when
® MASTER ON/OFF
is pressed
inward to the ON position.
• Basically, we recommend that you use the standby mode to turn
off this unit.
4
5
Press @STRAIGHT' repeatedly to select
"SQMIN".
Press @MASTER QlN/OFF to release it
outward to the
OFF
position to save the new
setting and turn off this unit.
•
Set the main zone to the standby mode
Press @MAIN ZONE ON/OFF (or CVSTANDBY)
to set the main zone to the standby mode.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
Note
The setting you made is reflected next time you turn on this unit.
•
Turning on the main zone from the
standby mode
Press @MAIN ZONE ON/OFF (or @POWER) to
turn on the main zone.
• When you turn on this unit, there will be a delay for a few
seconds before this unit can reproduce sound.
• These buttons are operational only when
®MASTER ON/
OFF
is pressed inward to the ON position.
If there are some problems...
• First, turn off and then turn on this unit again.
• If problems persist, initialize the parameters of this
unit. See page 129 for details.
33
En
Setting the speaker impedance
Caution
If you are to use 6 ohm speakers, set '"SPEAKER
IMP." to '"6Q MIN" as follows BEFORE using this
unit. You can also use 4 ohrn speakers as the front
speakers.
Connections
Turninglhis.unit ·.on.·and .011
•
Turning on this unit
Press @MASTER ON/OFF on the front panel
inward to the ON position to turn on this unit.
When you turn on this unit by pressing @MASTER ONI
OFF,
the main zone is turned on.
1
2
Make sure this unit is turned off.
Press and hold @S1
I
RAIGHT on the front
panel and then press @MASTER ON/OFF
inward to the ON position to turn on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
,I,
':-(j)-:'
When you turn on this unit, there will be a delay for a few
seconds before this unit can reproduce sound.
•
Turning off this unit
Press @MASTER ON/OFF on the front panel
again to release it outward to the
OFF
position to
turn off this unit.
Rotate the @PROGllAM selector to select
"SPEAKER IMP.".
3
STRAIGHT
~
While holding
dClwn
....
~
Notes
• @MAIN ZONE ON/OFF
on the front panel as well as
@POWER
and
C1)STANDBY
on the remote control are
operational only when
® MASTER ON/OFF
is pressed
inward to the ON position.
• Basically, we recommend that you use the standby mode to turn
off this unit.
4
5
Press @STRAIGHT' repeatedly to select
"SQMIN".
Press @MASTER QlN/OFF to release it
outward to the
OFF
position to save the new
setting and turn off this unit.
•
Set the main zone to the standby mode
Press @MAIN ZONE ON/OFF (or CVSTANDBY)
to set the main zone to the standby mode.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
Note
The setting you made is reflected next time you turn on this unit.
•
Turning on the main zone from the
standby mode
Press @MAIN ZONE ON/OFF (or @POWER) to
turn on the main zone.
• When you turn on this unit, there will be a delay for a few
seconds before this unit can reproduce sound.
• These buttons are operational only when
®MASTER ON/
OFF
is pressed inward to the ON position.
If there are some problems...
• First, turn off and then turn on this unit again.
• If problems persist, initialize the parameters of this
unit. See page 129 for details.
33
En