Yamaha RX-V1800 Owner's Manual page 117

Usin multi-zone confi uration
• Turning on or off Zone 2 and/or Zone 3
using the remote control
@POWER and (J)STANDBY on the remote control
work differently depending on the selected zone that
appears in the display window
(@)
on the remote control.
• When the main zone, Zone 2 or Zone 3 mode is
selected, you can tum on the main zone, Zone 2 or
Zone 3 or set them to the standby mode individually.
• When the all mode is selected, pressing @ POWER
turns on the main zone, Zone 2 and Zone 3
simultaneously and pressing (J)STANDBY sets them
to the standby mode simultaneously.
• You must complete this step within 10 seconds while the
selected zone flashes in the front panel display. Otherwise,
the currently selected zone mode is autOInatically
canceled. In this case, press
®ZONE CONTROLS
again.
• The initial setting is ZONE2 when both Zone 2 and Zone 3
are turned on.
3
Refer to "Selecting tlhe input source of Zone
2 or Zone 3", "Adjusting the volume level of
Zone 2 or Zone 3", "J~djusting the balance of
the speaker level in Zone 2 or Zone 3" or
"Adjusting the tonal quality of Zone 2 or
Zone 3" on page 114 to perform further
operations.
Remote control operations
Main zone
mode
Name of the selected
input area
Turns on the main
zone only or sets it to
the standby mode.
Set the operation mOlde selector to @AMP
and then press @5E:LECT
f1
repeatedly to
select the zone you \jvant to control.
"ZONE 2" or "ZONE 3'" is displayed in the display
window
(@)
on the remote control.
®
POWER:
turns on
the main zone. Zone
2 and Zone 3.
Q)STANDBY: sets
the main zone. Zone
2 and Zone 3 to the
standby mode.
Turns on Zone 2 or
sets it to the standby
mode.
Turns on Zone 3 or
sets it to the standby
mode.
"ALL"
All mode
"ZONE 3" or ""3:name
Zone 3 mode
of the selected input
area"
"ZONE 2" or "2:name
Zone 2 mode
of the selected input
area"
Notes
• When the remote control is in the main zone mode. ""MAIN"
appears for a few seconds when
@POWER
or
Q)STANDBY
is pressed.
• "ALL" appears in the display window
(@)
on the remote
control only when
@SELECT
V
is pressed.
or
Refer to "Selecting the input source of Zone
2 or Zone 3", "Adjusting the volume level of
Zone 2 or Zone 3", "J~djusting the balance of
the speaker level in 2:one ,2 or Zone 3" or
"Adjusting the tonal quality of Zone 2 or
Zone 3" on page 114 to perform further
operations.
2
1
3
Press @5ELECT f11
V
to exit from the
Zone 21Zone 3 mode.
113
En
Usin multi-zone confi uration
• Turning on or off Zone 2 and/or Zone 3
using the remote control
@POWER and (J)STANDBY on the remote control
work differently depending on the selected zone that
appears in the display window
(@)
on the remote control.
• When the main zone, Zone 2 or Zone 3 mode is
selected, you can tum on the main zone, Zone 2 or
Zone 3 or set them to the standby mode individually.
• When the all mode is selected, pressing @ POWER
turns on the main zone, Zone 2 and Zone 3
simultaneously and pressing (J)STANDBY sets them
to the standby mode simultaneously.
• You must complete this step within 10 seconds while the
selected zone flashes in the front panel display. Otherwise,
the currently selected zone mode is autOInatically
canceled. In this case, press
®ZONE CONTROLS
again.
• The initial setting is ZONE2 when both Zone 2 and Zone 3
are turned on.
3
Refer to "Selecting tlhe input source of Zone
2 or Zone 3", "Adjusting the volume level of
Zone 2 or Zone 3", "J~djusting the balance of
the speaker level in Zone 2 or Zone 3" or
"Adjusting the tonal quality of Zone 2 or
Zone 3" on page 114 to perform further
operations.
Remote control operations
Main zone
mode
Name of the selected
input area
Turns on the main
zone only or sets it to
the standby mode.
Set the operation mOlde selector to @AMP
and then press @5E:LECT
f1
repeatedly to
select the zone you \jvant to control.
"ZONE 2" or "ZONE 3'" is displayed in the display
window
(@)
on the remote control.
®
POWER:
turns on
the main zone. Zone
2 and Zone 3.
Q)STANDBY: sets
the main zone. Zone
2 and Zone 3 to the
standby mode.
Turns on Zone 2 or
sets it to the standby
mode.
Turns on Zone 3 or
sets it to the standby
mode.
"ALL"
All mode
"ZONE 3" or ""3:name
Zone 3 mode
of the selected input
area"
"ZONE 2" or "2:name
Zone 2 mode
of the selected input
area"
Notes
• When the remote control is in the main zone mode. ""MAIN"
appears for a few seconds when
@POWER
or
Q)STANDBY
is pressed.
• "ALL" appears in the display window
(@)
on the remote
control only when
@SELECT
V
is pressed.
or
Refer to "Selecting the input source of Zone
2 or Zone 3", "Adjusting the volume level of
Zone 2 or Zone 3", "J~djusting the balance of
the speaker level in 2:one ,2 or Zone 3" or
"Adjusting the tonal quality of Zone 2 or
Zone 3" on page 114 to perform further
operations.
2
1
3
Press @5ELECT f11
V
to exit from the
Zone 21Zone 3 mode.
113
En