Getting Started - Yamaha RX-V1800 Owner's Manual

Getting started
• Installing batteries in the remote control
1
Press the
v
part and slide the battery
compartment cover ()ff.
2
Insert the four suppliied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and -) on the inside of the
battery compartmen1t.
3
Slide the cover back until it snaps into place.
• Installing batteries in the Zone 2/Zone 3
remote control (Except Europe model)
1
Take off the battery compartment cover.
2
Insert the two supplifed batteries (AAA, R03,
UM-4) according to the polarity markings
(+ and -) on the insidle of the battery
compartment.
3
Snap the battery conlpartment cover back
into place.
Notes
• Change all of the batteries if you notice the following
conditions:
- the operation range of the remote control decreases.
- the transmit indicator (@) does not flash or its light becomes
dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the san1e shape and
color.
• If the batteries have leaked. dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing. etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throwaway batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes. or if exhausted batteries remain in the remote controL
the contents of the memory may be cleared. When the memory
is cleared. insert new batteries. set up the remote control code
and program any acquired functions that may have been
cleared.
• VOLTAGE SELECTOR
(Asia and General models only)
Caution
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local voltage BEFORE
plugging the power cable into the AC wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a straight
slot screwdriver.
Voltages are as follows:
........................AC 110/120/220/230-240 V, 50/60 Hz
VOLTAGE
SELECTOR
"". Voltage indication
5
En
Getting started
• Installing batteries in the remote control
1
Press the
v
part and slide the battery
compartment cover ()ff.
2
Insert the four suppliied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and -) on the inside of the
battery compartmen1t.
3
Slide the cover back until it snaps into place.
• Installing batteries in the Zone 2/Zone 3
remote control (Except Europe model)
1
Take off the battery compartment cover.
2
Insert the two supplifed batteries (AAA, R03,
UM-4) according to the polarity markings
(+ and -) on the insidle of the battery
compartment.
3
Snap the battery conlpartment cover back
into place.
Notes
• Change all of the batteries if you notice the following
conditions:
- the operation range of the remote control decreases.
- the transmit indicator (@) does not flash or its light becomes
dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the san1e shape and
color.
• If the batteries have leaked. dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing. etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throwaway batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes. or if exhausted batteries remain in the remote controL
the contents of the memory may be cleared. When the memory
is cleared. insert new batteries. set up the remote control code
and program any acquired functions that may have been
cleared.
• VOLTAGE SELECTOR
(Asia and General models only)
Caution
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local voltage BEFORE
plugging the power cable into the AC wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a straight
slot screwdriver.
Voltages are as follows:
........................AC 110/120/220/230-240 V, 50/60 Hz
VOLTAGE
SELECTOR
"". Voltage indication
5
En