Yamaha RX-V1800 Owner's Manual page 93

Input/output assignment:
I . . . . .
I]
!:~ ~::;
S I
l~:i
i · ··II·' · 1
E t··j·r
Use this feature to assign the input/output jacks according
to the component to be used if the initial settings of this
unit do not correspond to your needs. Change the
parameter to reassign the respective jacks and effectively
connect more components.
Once the input/output jacks are reassigned, you can select
the corresponding component by using the
@INPUT
selector on the front panel (or the input selector buttons on
the remote control).
~\r.r~
• "NONE" appears in the OSD when any input source is not
assigned to the input/output jack.
• You cannot select a specific item more than once for the same
type of jack.
• An asterisk
(*)
appears to the right of the input/output jack
names that have heen changed from their previous settings.
• The currently assigned input source for the selected input/
output jack appears in the OSD ('"Current( DTV/CBL )" in the
display example ahove).
In put rename
I
I···j
i:::' ! ..J·r i:;~~ E: "· · 1
!:::II' I ' I
i l : : : :
Use this feature to change the name of the input source
that appears in the OSD and in the front panel display.
~\r.r~
You can also change the name of the input source that appears in
the display window
(@)
on the renlote control. Refer to
"Changing source names in the display window" on page lOS.
1
Press @<J I
C>
to plaIce the "_" (underscore)
under the space or the character you want to
edit.
Customizing this unit (MANUAL SETUP)
2 Press @ ~ I
V
to select the character you
want to use and then press @<J I
C>
to move
to the next space.
Notes
• You can use up to 9 characters for each input.
• Press
@
\I
to change the character in the followi ng order.
or press
@
L.
to go in the reverse order:
A to Z, 0 to 9, a to
l,
symbols (#, , -,
+,
etc.), space.
3
Repeat steps 1 through 2 to rename each
input source.
4
Press @ ENTER to complete.
Volume trim
I.)
()I. . . .
II
T'F~ I ' ' ' - 1
Use this feature to adjust the level of the signal input at
each jack. This feature is useful if you want to balance the
level of each input source to avoid sudden changes in
volume when switching between input sources.
Control range: -6.0 dB to +6.0 dB
Control step: 0.5 dB
Initial setting: 0.0 dB
This parameter also affects the signals output at the audio ZONE
OUT jacks.
Decoder mode [)i::::C::C)I)E::I:;~~
j' I ' I C)[)I::::
Use this feature to switch the decoder activation mode.
You can designate the reassigned digital input jacks for
DTS signals.
..~.
AUTO
DTS
Automatically detects digital audio signal input
types and selects the appropriate decoder.
Activates the DTS decoder \vhen digital audio
signals are input.
89
En
Input/output assignment:
I . . . . .
I]
!:~ ~::;
S I
l~:i
i · ··II·' · 1
E t··j·r
Use this feature to assign the input/output jacks according
to the component to be used if the initial settings of this
unit do not correspond to your needs. Change the
parameter to reassign the respective jacks and effectively
connect more components.
Once the input/output jacks are reassigned, you can select
the corresponding component by using the
@INPUT
selector on the front panel (or the input selector buttons on
the remote control).
~\r.r~
• "NONE" appears in the OSD when any input source is not
assigned to the input/output jack.
• You cannot select a specific item more than once for the same
type of jack.
• An asterisk
(*)
appears to the right of the input/output jack
names that have heen changed from their previous settings.
• The currently assigned input source for the selected input/
output jack appears in the OSD ('"Current( DTV/CBL )" in the
display example ahove).
In put rename
I
I···j
i:::' ! ..J·r i:;~~ E: "· · 1
!:::II' I ' I
i l : : : :
Use this feature to change the name of the input source
that appears in the OSD and in the front panel display.
~\r.r~
You can also change the name of the input source that appears in
the display window
(@)
on the renlote control. Refer to
"Changing source names in the display window" on page lOS.
1
Press @<J I
C>
to plaIce the "_" (underscore)
under the space or the character you want to
edit.
Customizing this unit (MANUAL SETUP)
2 Press @ ~ I
V
to select the character you
want to use and then press @<J I
C>
to move
to the next space.
Notes
• You can use up to 9 characters for each input.
• Press
@
\I
to change the character in the followi ng order.
or press
@
L.
to go in the reverse order:
A to Z, 0 to 9, a to
l,
symbols (#, , -,
+,
etc.), space.
3
Repeat steps 1 through 2 to rename each
input source.
4
Press @ ENTER to complete.
Volume trim
I.)
()I. . . .
II
T'F~ I ' ' ' - 1
Use this feature to adjust the level of the signal input at
each jack. This feature is useful if you want to balance the
level of each input source to avoid sudden changes in
volume when switching between input sources.
Control range: -6.0 dB to +6.0 dB
Control step: 0.5 dB
Initial setting: 0.0 dB
This parameter also affects the signals output at the audio ZONE
OUT jacks.
Decoder mode [)i::::C::C)I)E::I:;~~
j' I ' I C)[)I::::
Use this feature to switch the decoder activation mode.
You can designate the reassigned digital input jacks for
DTS signals.
..~.
AUTO
DTS
Automatically detects digital audio signal input
types and selects the appropriate decoder.
Activates the DTS decoder \vhen digital audio
signals are input.
89
En