Yamaha RX-V1800 Owner's Manual page 42

Optimizing the speaker setting for your listening room
4
Press @ENTER to start the setup
procedure.
This unit starts the automatic setup procedure. Loud
test tones are output from each speaker during the
automatic setup procedure. Once all items are set, the
result display appears in the OSD.
Notes
• During the automatic setup procedure, do not perform any
operation on this unit. If you perform any operation while
this unit is in the automatic setup procedure, "E-9:USER
CANCEL" appears in the OSD. In such cases, select
"RETRY" to restart the automatic setup procedure.
• We recommend that you get out of the room while this unit
is in the automatic setup procedure. Keep quiet when you
leave the room.
It
takes approximately 3 minutes for this
unit to complete the automatic setup procedure.
The display changes as follows.
.. ;..
Ii
I=II...ITO ~:::;ET'UF'
The results displayed under "RESULT" are as follows.
Number of speakers
5P
Displays the number of speakers connected to this
unit in the following order:
Front/Back/Subwoofer
Speaker distance
DI 5T
Displays the speaker distance from the listening
position in the following order:
Closest speaker distanceIFarthest speaker distance
Speaker level
LI.,.lL
Displays the speaker output level in the following
order:
Lowest speaker output level/Highest speaker output
level
Notes
• If "E-I O:INTERNAL ERROR" appears during the testing
procedure, restart from step 2.
• When this unit detects potential problems during the
automatic setup procedure, "WARNING" and the number
of warning messages appears in the above of "RESULT"
(see page 4] ).
• Depending on the listening environment, "SWFR
PHASE:REV" appears during the automatic setup
procedure and "SUB WOOFER PHASE" in "SOUND
MENU" (see page 82) is automatically set to
"REVERSE".
5
Press @ENTER to display the setup results
in detail.
..
~.
.
.;..
38
En
Optimizing the speaker setting for your listening room
4
Press @ENTER to start the setup
procedure.
This unit starts the automatic setup procedure. Loud
test tones are output from each speaker during the
automatic setup procedure. Once all items are set, the
result display appears in the OSD.
Notes
• During the automatic setup procedure, do not perform any
operation on this unit. If you perform any operation while
this unit is in the automatic setup procedure, "E-9:USER
CANCEL" appears in the OSD. In such cases, select
"RETRY" to restart the automatic setup procedure.
• We recommend that you get out of the room while this unit
is in the automatic setup procedure. Keep quiet when you
leave the room.
It
takes approximately 3 minutes for this
unit to complete the automatic setup procedure.
The display changes as follows.
.. ;..
Ii
I=II...ITO ~:::;ET'UF'
The results displayed under "RESULT" are as follows.
Number of speakers
5P
Displays the number of speakers connected to this
unit in the following order:
Front/Back/Subwoofer
Speaker distance
DI 5T
Displays the speaker distance from the listening
position in the following order:
Closest speaker distanceIFarthest speaker distance
Speaker level
LI.,.lL
Displays the speaker output level in the following
order:
Lowest speaker output level/Highest speaker output
level
Notes
• If "E-I O:INTERNAL ERROR" appears during the testing
procedure, restart from step 2.
• When this unit detects potential problems during the
automatic setup procedure, "WARNING" and the number
of warning messages appears in the above of "RESULT"
(see page 4] ).
• Depending on the listening environment, "SWFR
PHASE:REV" appears during the automatic setup
procedure and "SUB WOOFER PHASE" in "SOUND
MENU" (see page 82) is automatically set to
"REVERSE".
5
Press @ENTER to display the setup results
in detail.
..
~.
.
.;..
38
En