Programming Codes From Other Remote Controls - Yamaha RX-V1800 Owner's Manual

Remote control features
3
Press @LEARN using a ballpoint pen or
similar object.
"LEARN" and the name of the selected input area
(e.g. "DVD") appear alternately in the display
window (@) on the remote control.
ooooo~./
0000 [
0000
Other remote control
I~
· 1
5 to 10 cm (2 to 4 in)
.. . . .. • • • .lI ~
.................................
1 · . < 1:>< • • • • 1 - • • • •
I ' •••• I I • • • • • • •
I . - . ' ' ••••• 1 - ' - • . • • •
I. I " : • • •
" 1 . I::"
'1:.11 ,..... ,. ~ II' 111" •
Place this remote control about 5 to 10 cm
(2 to 4 in) apart from the other remote control
on a flat surface so that their infrared
transmitters are aimed at each other.
2
~YAMAHA
Set to
SOURCE
.J.
t
Programming codes from other
remote controls
You can program remote control codes from other remote
controls. Use the learn feature if you want to program
functions not included in the basic operations covered by
the remote control codes, or an appropriate remote control
code is not available. You can program the function of
other remote control to the buttons in the highlighted areas
in the following illustration. The buttons can be
programmed independently for each input area.
Note
The remote control transmits infrared rays. If the other remote
control also uses infrared rays. this remote control can learn most
of its functions. However. you may not he ahle to program some
special signals or extremely long transmissions. Refer to the
operating instructions for the other remote control.
1
Set the operation mode selector to
@SOURCE and then press an input selector
button (CD) or
u
to select an input area.
!
Notes
• Do not press and hold
@LEARN.
If
you hold it down for
more than 3 seconds. the remote enters the remote control
code setting mode.
• If you do not complete each of the following steps within
30 seconds. the learning mode will he automatically
canceled. In this case. start over from step 3.
Note
1\1ake sure that the operation mode selector is set to
@SOURCE.
When you set the operation mode selector to
@AMP
and
program a remote control codes from other remote controls. the
programmed key cannot operate the amplifier function of this
unit.
4
Press the button for which you want to
program the new function.
"LEARN" appears in the display window
(@)
on the
remote control.
Ii. - -- ..
• .',,', ' , ' , ' • , ' , ' '1',"
I 1.--- " , _ " ','
.1"".
• •••• 1 . 1 ••••
I I . ' • ".- ••••••• ' "1'
• " , _ • • I - I " 1 '
".iII1 ...... , . - " , ' " , . ' .
104
En
Remote control features
3
Press @LEARN using a ballpoint pen or
similar object.
"LEARN" and the name of the selected input area
(e.g. "DVD") appear alternately in the display
window (@) on the remote control.
ooooo~./
0000 [
0000
Other remote control
I~
· 1
5 to 10 cm (2 to 4 in)
.. . . .. • • • .lI ~
.................................
1 · . < 1:>< • • • • 1 - • • • •
I ' •••• I I • • • • • • •
I . - . ' ' ••••• 1 - ' - • . • • •
I. I " : • • •
" 1 . I::"
'1:.11 ,..... ,. ~ II' 111" •
Place this remote control about 5 to 10 cm
(2 to 4 in) apart from the other remote control
on a flat surface so that their infrared
transmitters are aimed at each other.
2
~YAMAHA
Set to
SOURCE
.J.
t
Programming codes from other
remote controls
You can program remote control codes from other remote
controls. Use the learn feature if you want to program
functions not included in the basic operations covered by
the remote control codes, or an appropriate remote control
code is not available. You can program the function of
other remote control to the buttons in the highlighted areas
in the following illustration. The buttons can be
programmed independently for each input area.
Note
The remote control transmits infrared rays. If the other remote
control also uses infrared rays. this remote control can learn most
of its functions. However. you may not he ahle to program some
special signals or extremely long transmissions. Refer to the
operating instructions for the other remote control.
1
Set the operation mode selector to
@SOURCE and then press an input selector
button (CD) or
u
to select an input area.
!
Notes
• Do not press and hold
@LEARN.
If
you hold it down for
more than 3 seconds. the remote enters the remote control
code setting mode.
• If you do not complete each of the following steps within
30 seconds. the learning mode will he automatically
canceled. In this case. start over from step 3.
Note
1\1ake sure that the operation mode selector is set to
@SOURCE.
When you set the operation mode selector to
@AMP
and
program a remote control codes from other remote controls. the
programmed key cannot operate the amplifier function of this
unit.
4
Press the button for which you want to
program the new function.
"LEARN" appears in the display window
(@)
on the
remote control.
Ii. - -- ..
• .',,', ' , ' , ' • , ' , ' '1',"
I 1.--- " , _ " ','
.1"".
• •••• 1 . 1 ••••
I I . ' • ".- ••••••• ' "1'
• " , _ • • I - I " 1 '
".iII1 ...... , . - " , ' " , . ' .
104
En